I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
i have a few question, i bought this " www.skylabmodule.com/.../".
if the device has a sample code loaded?
where are the example codes for the device?
i want connect...
Hi everyone,
I recently acquired a nRF52832 Breakout Board from Sparkfun. I have been using it for a few weeks now and everything was fine. I was programming it using the...
I use DFU function to update APP. and when i execute the flash write operatin in APP,then afer the dfu operation,bootloader can not jump to the APP. it keeps in bootloadr...
I am using nrf52832, SDK14 and sd 132.5.0. I want to disable SAADC after measuring battery level then enable again when I want to measure it again like in this post . When...
Hi, I want to know how to properly indicate for the function
spi_send_recv(...)
that I'm sending or receiving data on SPI.
On other platforms with library function...
I'm using the SPI driver and experiencing a hang in the SPI driver because the SPI interrupt is not raised. The reason is in this code from the driver:
p_cb->bytes_transferred...
Hi,
my device does some UART communication. Because temperature drift of HFINT is to large, the external HFXO has to be used. To make things worse, this is a low power...
hello,
I modified the beacon example that allows me to modify major and minor value from mobile app,
but when i restart the nrf52840 dev board, the modified values are reset...
Hi,
I need to get at least 3 sensors data (Accelerometer and Gyro) simultaneously and I am thinking to use the Nordic Thingy:52 for that. Our application sends these information...
Hello Nordic Devzone,
I have problems with twi/i2c init code on a Micro:bit, nrf51822.
The accelerometer is a Freescale MMA8652FC.
I use Segger Embedded Studio for ARM...
Hi there,
We started to notice that we have been getting random disconnects with the reason BLE_HCI_CONNECTION_TIMEOUT. After profiling our device, it was found on one...
Hello everybody,
I try to use fstorage in SDK 14.2.0 S132 with Segger Embedded Studio IDE.
I write this;
static ret_code_t fds_init (void)
{
ret_code_t ret = fds_register...
I have been using the RF Digital Simblee chip ( also with the NRF51822) with my Android app and Java code to communicate with the Simblee chip as a peripheral.
I have been...
hi nordic;
i need your help, i'm trying to code a control of gpio over the BLE i have an app on android with it i can establish connection and see the service and charactrestic...
This is not a duplicate of:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I have tried to implement the accepted answers...
