According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
There are parallel 8 bits input to nrf52832 GPIO pins,I want to read the data from the pins and writ it to a RAM.how to do read the data in one CPU clock?
As per this document ....
nrf5_SDK_for_Mesh_v1.0.1_src/doc/introduction/mesh_hw_resources.md
The mesh stack uses flash to store the following states:
- Encryption keys...
We modified the ble_app_beacon example to advertise the beacon once a second.
#define NON_CONNECTABLE_ADV_INTERVAL MSEC_TO_UNITS(1000, UNIT_0_625_MS)
As a result of...
Hello all.
Sorry for the nube question, but I am really struggling to try and get my IMU data from my MPU9250, to send constant notifications through BLE using the NRF8001...
When using BLE_GATTS_VLOC_USER I would tend to make the variable pointed to by ble_gatts_attr_t.p_value volatile to reflect the situation that the value can be changed by...
Hello,
I am new to nrf5 mesh. I have setup my system based on Nordic's documentation and was evaluating Serial Example with Interactive Py script.
My setup consists of...
Hi:
I have a project which nrf51822 exchange some data with TI cc2541.There is a serious issue that the nrf51822 is occasionally reset by the watchdog when it communiates...
Hello all
I am trying to get out some debug messages from my custom Firmware (and board) but the log looks like this:
<info> µ“°8$Mø@ñ¨ó¹)F¨: NRF_LOG initialized
...
Hi,
can you please to provide a more information regard power up sequence?
for example:
we would like to use DC2DC (instead LDO) with CR2032 battery.
the PCB have...
Hi all,
I am trying to send a command to the sensor so that the sensor will response with sending something back for acknowledgement, via UART.
Let say, I want to send...
Does anyone have experience about range, robustness, link stability etc. for Bluetooth 4.0/5.0 (using nRF52832) compared to the old Bluetooth 3.0 standard? For some applications...
Hello guys, I am the newbie with this development board. I want to know that how I can write a simple led program or can upload any example into nrf52840 using window operating...
I'm trying to print received data on my com port but when I set the "NRF_LOG_ENABLED" as 1 the error below shows up.
What does it mean?? How would I know what files to...
Hi There,
I'm just getting started with ARM and the NRF52832. I've done a lot of work with 8-bit micros and I'm interested in learning 32-bit and in porting some old AVR...
