Dear all,
1) I flash the code through the debugger to my pcb and it is running correctly (just on/off some LEDs).
2) I remove the JTAG+SWD connector, the project still...
Hi, We’re trying to develop a way to create fully self-contained repositories that include:
-the toolchain
-the entire SDK
-the necessary tools (for example, flashing...
Hello, I want to build serial_lte_modem sample for a custom board based on nRF9151, but it fails with this error:
error: Aborting due to Kconfig warnings
I can build...
Hi,
I'm using the nRF52832 with SDK version 17.0.1 , and I'm experiencing an issue with NFC handling .
Sometimes, the NFC interrupt triggers two FIELD_OFF or two FIELD_ON...
Hi Nordic team,
This is a compatibility test. case1 okay: 1,Connect the nRF5340BIS headset with the phone. 2,NRF5340 broadcast can be found on the mobile phone. 3,When you...
first i change to my kconfig file add this
source "samples/subsys/usb/common/Kconfig.sample_usbd"
source "Kconfig.zephyr
second I add to cmakelits
include...
NRF52840
S140
App based on ble_app_multilink_central.
I have tried to build a bridge between BLE peripheral and PC.
I have spend so many time on PC side app.
The...
Hi Everyone,
I have what I hope is a simple questions. I am creating a piece of hardware that will act as the peripheral to a central iOS app in regards to a standard BLE...
Is there any construction available in the SDK, to achieve printing functions, with an undefined number of parameters ? The classic example :
#ifdef CONFIG_DEBUG
#define...
Hello,
I've ready the final S130 spefication and it states that the advertiser is started as early as possible and that i runs asynchronously to all other roles. Now I...
Calling app_sched_event_put() from the NRF_RADIO_CALLBACK_SIGNAL_TYPE_START signal handler causes a crash due to the CRITICAL_REGION_ENTER() call inside of app_sched_event_put...
is there any code for device which act as master and peripheral other than nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental \app_s130_demo\pca10028...
I have a simple nRF51822 BLE application where a voltage is read by ADC periodically, and several values are sampled and averaged. However, from time to time, I get another...
Hello All ,
I am working on nrf51822 with sdk 7.1.0 and softdevice 7.1.0 .Earlier my ble connection was working very good with no disconnection anytime unless i disconnect...
Now I'm working with MCP 3.9.0.
When any device is connected, characteristic default values are not 0's. Can they be initialized in any way? It is a little bit annoying when...
Is there a separate reference resign for the 1.8V of operation (as in case of nrf51)? Or it's implicit and the chip can be powered in range of 1.7V - 3.6V.
Thank you!
I am using nrf51442 as central client.
I have used
SDK\v7.1.0\examples\ble_central\ble_app_hrs_c\pca10028\s120\arm\ble_app_hrs_c_s120_pca10028.uvproj" as a atart point...
Hi All,
I am integrating Johanson's balun and Nordic's L shaped pcb antenna, is it possible to have the antenna connected directly to the balun's pad? as in the below pcb...
The m_client_count is like instantly increased when I power up another (or the first) peripheral.
But with increasing connection interval the time till the central finally...
Hello,
i want to implement DFU with the S130. The problem is, that I currently do not use the device manager because I need both Central and Peripheral connections at the...
Hello,
This is an add-on question to the the one outlined in:
devzone.nordicsemi.com/.../
That question states that:
The maximum SoftDevice size that can be updated...
I've got the nRF52 preview development kit and I am trying to flash a binary in it.
I am using JLink_Linux_V501a_x86_64 the way I was using for nRF51, but I can't get anything...
