nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Something did change in the last 2 days but I dont know what.
On tuesday I was able to connect with my mobile device to the nRF51-DK. The application worked fine and it...
I'm using SDK 7.1, PCA10028 and SD310 v2.0.1
Is there a project that implements OOB protection for bonding?
My device has no display, and a single button for input....
I'm getting Error 7 too few arguments to function 'lib_aci_set_local_data' C:\Users\nishant\Documents\Atmel Studio\6.2\ATmega_AdafruitLIB_nRF8001\ATmega_adafruitLIB_nRF8001...
Hello,
as far as I found out, a Peripheral that advertises will stop advertising as soon as it receives an incoming connection (BLE_GAP_EVT_CONNECTED). A central will however...
I'm using the nrf51822 with the IoT softdevice and SDK as an IPv6/6LoWPAN peripheral and Linux with a BLE dongle in the central role. Basically, I have everything working...
I'm trying to write 7 bytes (0x01 02 03 04 05 06 07) to my nrf51 Dongle with my own custom service running based on the Battery Service.
The problem is that I can only...
Why does it say that the nRF51822 has 1Mb/s and 2Mb/s data rates if it doesn't?
Quote from devzone: "6 * 20 B* 1/0.0075 s = 16 kB/s = 128 kbps".
And its only for S110...
Hi there
I am having problems with uart app on SDK V7.2
I have dowloaded Keil and all of the other demo's seem to be working but this one is not.
It will not connect...
Hi. i have a little problem.
For start, i want to use the referance Layout found here link text with the hardware description file of PCA10004.
So there is a simple method...
Previously, I used to load and debug my programs.
after a few months,
Today when I setup the environment again, now I can only compile and generate hex files from Keil....
Hi,
Now I am try to use sd_flash_page_erase() to erase a flash page.
Before I call it, I already stop all interrupt but I always get a error message "NRF_ERROR_NO_MEM...
Hello,
I am working with nRF51822 development kit (s130 softdevice). I want to use one software interrupt for my custom application. Is there any software interrupt available...
During my development with ANT protocol, I found that if you have a bunch of units all have one master channel. Channels will actually bump into other channels easily and...
