Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I'm looking at the output of nm on my ELF file:
20002004 00000002 d heart_rate /path/to/Debug/../src/ble.c:132
.
.
.
200028ac D __data_end__
200028ac D __data_start__...
Hello,
I've ordered the kit NRF51-DK, and waiting to be deliver.
NRF51-DK is including a J-link on board, my goal is to program this kind of cheap board with it just...
Is there a window in Keil uVision available to monitor how much flash and RAM I've consumed? I'm not seeing anything in the build output and am not sure where else to look...
Happy Christmas All.
I had a Keil ARM IDE and the rest of the software to get my PCA10001 for the EV board set up a while back by just following the instructions that came...
Dear all,
I use the softDevice S110 V7.0 together with the SDK v6.1.I
've modified the dfu_dual_bank_ble bootloader.
Instead of waiting for the button press, it would...
Hi,
Does the nRF51822 SDK support the generation and broadcast of dynamically changing MAC address (i.e. resolvable private address, Bluetooth 4.0 specs, Volume 3, Part...
Hi all,
i have a device with the nrf8001 module. I can connect this to a smartphone and send data through the UART protocol. After that i disconnect the device and i have...
I'm attempting to set up the GNU ARM Eclipse Plug-ins. I've created a few managed-build projects. I'm attempting to reproduce the results of the makefile in the hrs example...
I need to know whether the nRF24L01(+) has an open-collector IRQ output, or a full push-pull driver. The datasheet doesn't mention this fact.
The reason is, that I'm working...
Am I the only one to experience what seems to be a bug? (same code is running fine on a Nucelo board)
developer.mbed.org/.../
This code is to put in evidence a BUG in...
Hi all,
I use nRF51822, nrf51_sdk_v5_2_0_39364 and s110_nrf51822_6.0.0.Test ANCS, first with the iPhone connection is no problem. When I disconnect, connect a second iphone...
Hi:
I would like to Advertising Data and Scan Response Data which are added CompleteLocalName, the program does not work, it will reset. Why is that?I err_code = ble_advdata_set...
Hi all!
I've been trying to upload the official firmware (nrf51822_beacon_app.hex) to the nrf51822 bluetooth smart beacon kit. I put the beacon in bootloading mode (steady...
Hi,
Is there a way to modify any of the contents of the setup generated by nRFGo?
The services.h file generates SETUP_MESSAGES_CONTENT to populate setup_msgs[]
const...
