Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
hi.I have a question about synchronization. In main loop, there is a function sd_app_event_wait() which blocks until ble event from softdevice call occurs, so I want to put...
Thought I'd check to see if there were any examples floating around that demonstrate how to dynamically claim memory when the softdevice (s110) is disabled? Any hidden gotchas...
Hi All,
We have embedded windows ce devices, and were thinking of adding ble functionality by connecting a small nrf51822 board through a serial port.
Would it be possible...
I'm currently debugging a daughter card for the nRF8122 evaluation board but there's a higher voltage and current on that daughter card.
I want to know how the IO are connected...
We are developing an application based on S130 V0.9 (orignially S130 V0.5 was used) SoftDevice using development boards PCA10001/PCA10000/Beacon. Main activities of the application...
Hi,
I am trying to use the spi_slave_example on my nordic nrf51822. But i have an issue :
I can build all target and download code to flash memory but nothing happen...
Hello,
What is he meaning of PROTENSET0, PROTENSET1 in sd_flash_protect()?
How can I use this function to set WRITE PROTECT to a certain flash page?
I searched a lot...
Hi,
I need to use nrf51-ble-app-lbs application example to add my customized applications. I have downloaded the project but I'm not able to compile it probably cause I...
Hi All,
I am new in nrf51 development. I have a nRF51-DK kit. I would like to make development in Linux (Debian) only.
I found a lot of documents and I can compile examples...
I have read many times about how BT LE allows devices to run for more than a year on a coin cell.
However, the least current consumption I can obtain while connected is around...
Hello,
We are developing a system using a receiver nRF unit, and multiple transmitter nRF units. The transmitters use the proprietary radio protocol (not bluetooth LE)...
Hello,
I am trying to flash an application onto nRF8122 from an android mobile using the Nordic app. After pressing the DFU button, the programming fails giving a pop as...
I've been looking for information on GCC support for the DFU bootloader examples in SDK v7.2.0 for the BLE Dongle board(PCA10031) but unfortunately there's nothing in the...
