Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello, I'm developing an debugging an BLE application. I'm using nRF Sniffer (dongle) N51422 PCA10031. I can successfully sniff and decrypt ble secured connections of my application...
Hi all, I want to add light switch client to light switch proxy server . But I dont know how to get appkey handle for bind to light switch client . Pls , help me !! Thank...
Hello,
I'm unable to capture packets using the sniffer. Here are details regarding my set-up:
System: Debian 9.4 with kernel 4.9.0-4-amd64 #1 SMP Debian 4.9.65-3 (2017...
Many of the pins in the assignments page of the documentation are designated as "Standard drive, low frequency only" and I cannot seem to find an explanation of what is considered...
I am trying to connect my android mobile with nRF 52DK using BLE on the NRF TOOLBOX android application. But the nRF 52DK is not recognize by the NRF TOOLBOX APP(proximity...
Hello,
we have a problem using the SAADC module with the low power mode, particularly after execution of the NRF_SAADC->TASKS_SAMPLE task.
Before taking a sample, the...
Hello,
I have some questions about ble_conn_params.c in SDK14.2
Question :
1. a. Why do you need to handle four ble conditions ?
b. Shouldn't just send connect parameters...
I hope to use a acceleration sensor with nRF51822 dev kit. So I should use three ADC input. I tested getting one ADC data using adc_simple example(Keil_v5/ARM/Pack/NordicSemiconductor...
We use nRF52832 ,when new android phone will connect to this device by mac,we cannot connect to it successfully,we must scan to find the device first,after found it,we can...
I want to t o ensure the stability of BLE connection for BLE frequence calibration,but i don't know how to get the nordic into the test mode and broadcast the empty packet...
https://devzone.nordicsemi.com/f/nordic-q-a/9231/ble_hci_conn_failed_to_be_established-0x3e-problem/34074#34074
I also encountered the same problem as this one. How to solve...
Hi,
I am working on my nrf52840 dongle and it looks really cool to me. I just found an issue that, when my dongle enter DFU mode using DFU trigger, I can not return to the...
Quick question:
What IDE are most developers using?
I've seen both Eclipse & Segger being discussed.
I'm interested in having the best support, most libraries & examples...
I'm getting errors on trying to program a custom board using the Laird BL654. We are verifying manufacturing results with an x-ray of a populated board tomorrow checking for...
Details
Hardware: Thingy52, nRF52840 Dev Board, Samsung Tab A running Android 5.1.1
Software: Windows 10, using GCC for compilation, Thingy52 SDK, Android-Nordic-Thingy...
