I'm using 3.0.1 to compile an app for a nrf5340dk. It is building for 2.9.1, but errors on 3.0.1:
Line 51 is the first line of:
I thought that was the node label...
This is the power supply system in the nrf52832 development board. The manual means that when 1 and 2 are not powered, 3 is used for power supply, that is, cr2032 is used...
I have created my own project and board files for the development board I made. I have 3 I2C busses for different power domains, one SPI bus, and UART for debugging, so 5...
Hi,
I'm using the nRF52832 with SDK version 17.0.1.
I've noticed that when the device wakes up from NFC and remains in proximity to the NFC field, it sometimes experiences...
Greetings! I've applied all the optimizations in the books but I cannot get our application to be ~50% of the available flash memory on the NRF52832, currently it is precisely...
Hello,
I'm working on a project that involves using an NRF52832. Basically, I want to collect data, send it over bluetooth, and then have the device enter system_off mode...
Dear Sirs
I try to read SoftDevice version using
ble_version_t version; sd_ble_version_get(&version);
As I understand I get version of SoftDevice in field subversion_number...
It might be due to a short circuit caused by incorrect wiring. The PPK2 circuit board is damaged, and the chip with silkscreen "L7 #247" in the lower-right corner seems to...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
I followed the DevAcademy lesson on WiFi FOTA with AWS IoT, with some modifications to work with my board.
The device correctly connects to the AWS mqtt server and published...
Dear,
I’m experiencing an issue with performing DFU over BLE Mesh. I have a setup with one node acting as provisioner and distributor. This node has a new image loaded ...
I'm trying to flash a custom board (schematics in this ticket - Schematic/Layout review request ) using a Jlink EDU mini and keep running into an error message saying it's...
I'm having some trouble with the discovery module. The way the service I'm connecting to has the same UUID for the Bluetooth LE service as for its characteristic. I get this...
I'm developing a small IoT device that needs to retrieve and transmit its location upon pressing a button. While testing the modem using AT commands, I can consistently retrieve...
I am trying to adapt lesson 9 (FOTA over Wi-Fi) exercise 7 of the DevAcademy nRF Connect SDK Intermediate course. I am trying to adapt it to work with nrf52840 connected to...
Hi, my code will return ATT error code: 0x0E cyclically
I have check some tickets and try to update my central device to
Hoever, it still cannot, the error is like...
Hello,
I've been working on a project involving an IMU and bluetooth for a while, and had been using the IMU (LSM6DSO) on polling mode. Unfortunately, I found out that I...
I have two projects, project MQTT, that was built around the Secure MQTT Sensor/Actuator sample and project CRYPTO, that was built around the Crypto AES-CCM sample . I am...
I have an NRF52 devkit and trying to install the "blinky" sample for the first time, using VS Code.
I can build the firmware, but when I try to flash I get these errors...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
Hi Support,
I'm working on a project where I need to copy the contents of the internal flash from slot_0 to an external NOR flash partition. However, I'm currently unable...
