Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
Hello,
I have an external chip in SPI slave mode and connected to 52840 through SPI interface. When data is ready it will notify 52840 through its dedicated IRQ pin (connected...
Dear Nordic Team
We would like to use the following Chip device for one of our products:
NRF52811-QFAA-R
To this matter I have the following question:
1)Can you...
Hi
I'am trying to get working the nfc_uart_tag example from SDK16 on a nRF52840-DK with the IAR Workbench 8.42.2. As mentioned in the post IAR Library (v7.xx to v8.xx) compatibility...
Hi
Hi I’m cu rrently working with the given nordic project “ nrf52-ble-long-range-demo ”
I check peripheral and central BLE devices are transmitting emptyPDU packet after...
Hey all
I have to following setup:
nRF52840-DK (development kit)
Nordic SDK 15.3
Development using eclipse CDT (Makefile project)
I'd like to implement an EC...
I have a problem with building my nRF52832 projects. The problem is with nRF_drv_twi. When I started the project, I was able to compile the project. After some time, I didn...
hi,
I have issue with LwM2M Client sample code loading & compilation.
From the release note, NCS v1.1.0 can support LwM2M on the DK. Confirmed the sample code can be loaded...
Question/Problem Statement
For evaluation we decided to do some current measurements using the power profiler kit. As a benchmark run, we wanted to measure the current on...
hello,
I'm using NRF52840, developed android application NRF toolbox. The problem is that when I receive row data into BleManage to lagcat window but I can not find a proper...
Hi
How do you transmit using UART on segger. Up until now I have been using the debug console and the NRF_LOG_INFO command to send information from the DK to my computer...
The cloning instructions for the Cat tracker example fail:
https://bifravst.gitbook.io/bifravst/v/saga/cat-tracker-firmware/building#prepare-your-system
$ west init -m...
Hi I have two zigbee routers running the light bulb example, the thing is that it seems as they are not forming a mesh, Im doing the following:
1. Pair lightbulb 1 with...
Hi all,
I'm working on a custom Ble service based on this tutorial: https://github.com/bjornspockeli/custom_ble_service_example on nrf52840.
I've been able to add about...
Hi,
We are planning to use an Automotive Grade Bluetooth SoC in one of our new designs.
In the Product Specification of nRF5340, we have seen that the Operating Temperature...
