Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Should the toplevel declaration bool nrfx_power_irq_enabled; in nrfx_power.c have a `static` qualifier? I'm using openocd/gdb to load a GCC-compiled firmware onto a custom...
Hi,
I think I have properly configured my application to authorize reads on characteristic, yet I do not see an event generated. I get write events, but I don't get read...
Hi,
I am developing a custom board with nRF52811 where I will measure analog signals from op amp on ADC (single ended mode). Signals will be very small, so I need a good...
Hello guys. I'm beginner in Nordic Devices.
I'm working in project that sends Acceleration Data from KX220 sensor over LoRa network or if there is a BLE device connected...
Hi，
I find that nrf52 series can support Bluetooth 5.2 SoC in nordicsemi page, but it still shows Bluetooth 5.1 SoC in Product Spec.
Which one is right ? Is it just that...
In the User Guide for the nRF52840DK on pg 26 is:
8.5 External memory The nRF52840 DK has a 64 Mb external flash memory. The memory is a multi-I/O memory supporting both...
Hi,
I'm working with the USB_CDC_ACM example to communicate with a PC trough COM port. It works well.
Now I would like to use the ISO endpoint feature in order to transfer...
I have a NRF52840 DK, with a pca63511 power profiler kit purchased just a few days ago from Mouser. I am trying to use the power profiler kit with version 2.3.1 of the power...
We are in a need to upgrade the existing Soft Device to higher version from the application firmware. The reason why I am asking this, if it is possible to upgrade then we...
Hi All,
I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment
SDK - nRF5_SDK_16.0.0_98a08e2
IDE - Segger Embedded studio (windows 10 -...
I am using NRF52840 in Mesh (SDK 4.1.0), I am facing this strange issue, one of my node (have client+server both) is got damaged, I replaced this with new NRF52840, then I...
Dear support team,
In the AT command manual, the parameter type are well documented:
But there is no hint or description about parameters in certificate manager. The...
Hi I am using Mesh V 4.0 and Stack V 16.0
I have created the Message Model in Client side and can able to send string from Client to Server on button press.
Now when I...
I am a nRF new user, I try to use JLink-OB (STM32F072C8T6) program nRF52832 module, wire nRF52832 via SWD likes below,
I try to use nRF command Line tools operate nRF52832...
We're trying to make our device automatically recover after a brown-out or brief power loss. I'm hoping to leave a system-state value in a RAM location and check for it on...
