I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi,
There are several new drivers under "nRF5_SDK_15.0.0_a53641a\components\drivers_ext\", but no example now.
I have setup the HTS221 driver and it works. I turn to...
I'm using nRF52-DK, and following the quidelines from devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader . I'm using the prebuild "blinky_pca10040...
Im trying to interface nRF52DK to Custome build acceleration sensor.
I want to use I2C communication. Are the pin connections mentioned below sufficient?
...
The buttonless_dfu_sdh_state_observer in this example is shutting down the cpu when the softdevice is disabled using an observer.
I'm not sure why this is necessary...
Hi everyone,
I have a project written in C++ for nRF52 series using the SDK 15.3.
If I use Keil and uVIsion, the project compiles and works great. With the same source...
I am using nRF52832, And SDK 15.3, the ble_app_blinky project,
a. if i have installed only the latest version of Device family 8.29.0 , when i try to build the project,...
Setup and goal: I'm developing an BLE central app and would like to use scan address filtering to find a specific device. I enabled the filter and provided a hard-coded BD...
Hello,
I successfully downloaded SAADC SDK example in the peripheral folder. The hardware setup is as below ,
The pin configuration for this is as below
...
I tried implementing
https://github.com/andenore/NordicSnippets/blob/master/examples/temp/main.c
But i get 2.6V without connecting any of the Analog pins.
Exactly...
I have attached an Arduino INO file that I wrote early on in a project. It runs a probe. It is an amazingly simple probe but especially important. I am making a simple opacity...
Hi Team,
I planning to use vibration motor with nrf52832.
vibration motor will give maximum buzz on 20.3KHz(50 duty cycle).
So my question is
- Can I achieve 20...
Hello I would like to use the extended advertinsing packets from Blutooth V5 as used in the "ble_app_rscs" example. My problem is that I can't connect via the extended advertinsing...
It looks like NRF_LOG_INFO doesn't copy the data that is sent to it as per the below example. Is there a way around this so that I can reuse long buffers that contain either...
Our purpose is to integrate BLE 5 in our embedded application, and do it quickly.. We basically need to send/receive data with maximum throughput.
Per thread below, we are...
