Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi,
I'm trying to use the nrf52832 as the SPI master to get read/write flash ic MX25L6433FM2I-08G(address - 0x00 to 0xFF).
In loopback case got data but when interfacing...
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
I get started with Zigbee Door Lock Example in https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/zigbee_multi_dynamic_door_lock_nus_example...
Hi,
We have ordered nr51822 chips in the past. Recently, we made a new purchase and on programming we have discovered that the FICR register information is different for...
Hi Folks,
I am currently implementing a power down routine onto the nRF52840 SoC and I have some questions regarding the right way to configure to system On sleep mode...
Hi,
Is there an example code which can be used to evaluate libuarte while softdevice enabled? I have tried the individual examples in "nRF5_SDK_17.0.2\examples\peripheral...
Hello,
I would like to know what exactly is doing PM_HANDLER_SEC_DELAY_MS and how can affect to the interoperability.
I saw in the bms example (sdk 15.2) it is set to...
The BLE specification says that the CTE can be a maximum of 160us long. I am trying to set CTE length to 160us, but every time i try to do so, firstly the transmitter stops...
Hi Devzone:
We are using J-link pro to collect trace data from nRF52833 DK board, and we found a rather strange behavior:
The sw interrupts would end on its own without...
Hi,
I'm trying to connect an NRF52840-DK to a MAX30101 Wing board via I2C/TWI. I've set up the TWI Manager to send a message asking the MAX board for its part ID.
This...
nRF5340 with NCS 1.4.0.
I'm using the NUS (code derived from central_uart & peripheral_uart sample) and i'm trying to send longer frame.
I have tried to add the following...
Hello,
I was trying to recreate the blinky program for the nrf52840dk using the nRF5sdk using Segger embedded studio.
I tried doing it by opening the blinky example code...
Hello ,
I am using nRF52832 , sdk 16version. I want to set the BLE connection interval via BLE using application. How to do that? I tried to assign the variable to the min...
Hi everyone,
Regarding the CDC ACM example I have a question. In the example, every time a button is pressed there is a writing. I would like the writing to happen every...
We are trying to use more than one nRF52840 dongles simultanuously on the same PC and within the same process using the pc-ble-driver library (pc-ble-driver library version...
