Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi guys,
I am using the nRF52832 board and I want to parse and read my JSON file. I don't have too much experience working with cJSON and here you will find my simple code...
Hello,
While trying to build the hello_world project on Thingy 91 using the SEGGER (connection through J-link edu). Following the Hello World project guide given at:
Hello_World...
Hi, I am using BLE as transport and NRF_BL_DFU_ENTER_METHOD_BUTTONLESS as to enter into DFU mode.
My question is:
My application is running at the start and I wanna...
Hello, I wanted to migrate from sdk16 to sdk17, So according to this topic I solve all pre compiling errors, then when I tried to download the code on my board(nRF52832) I...
In the Buttons and LEDs page, the LEDs are connected to P0.28-31 but in the connector interface page, the Figure 1 show LEDs connected to P0.13-16.
Buttons pins also looks...
Hello,
I am trying to create an application on my nRF52-DK using several custom service peripherals, each with 2+ characteristics. I have completed a few tutorials on...
Hi,
I am using USB device CDC, and the COM Port name on the PC is "nRF52 USB CDC BLE Demo (COMX), see the picture below.
How I can change it ? can I change it from...
Hi,
I followed the instructions described on https://github.com/NordicSemiconductor/pc-nrfconnect-launcher but I cannot "Start scan" within nRF Connect. It's greyed out...
Hi,
We just received prototypes of a new board with the nRF52840 and now we have a reset problem.
When the board is reconnected after a long time (no voltage remains on...
Hello,
I am testing the multilink BLE (1 central : n peripheral) UART example.
I am using Github code and tested it.
The central example is(SDK 16.0.0):
https://github...
Hi, I've just compiled clean examples from Zigbee and Thread SDK 4.1.0 and I'm following instructions from here: I've got CLI on the nRF dongle and multi_sensor example loaded...
Hi Nordic experts:
I am working with sdk 17.0.2 nrf52840 ble_app_uart example project. I added twis i2c slave functionality in this project, and the project is working fine...
Hello everyone.
I want to assess the range of my current setup, theoretically. And I found this useful online "calculator": www.bluetooth.com/.../ (please scroll down until...
Hello,
I wanted to implement WDT resets when my application hangs. I am working on the advertiser code, what I observe was when I implement WDT driver in SDK 15.2 examples...
Hi,
I have been working with mesh and I'm using the version 4.2 Mesh SDK.As I understand it I should use nrf_mesh_serial_tx() api to send serial message.When I use this...
