Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Nordic's smart remote 3 is for nrf52832 and nrf52810.
I want to port the same on the nrf52840 DK.
I have basic IR receivers and Transmitter and want to integrate them...
I'm using the nrf52832 from fanstel (bt832) to stream audio to the adau1701 dsp. I want to be able to play music over Bluetooth. I'm using i2s to transfer the data to the...
Hello,
I am trying to change PHY after packet sent/received (known as asymmetric PHY).
After receiving EVENT_END, i write to register MODE to change the PHY.
This can...
Hi ,
I am using saadc to measure battery voltage i m using the sample example given as reference ble_app_proximity/
I am doing adc_configuration in one file and triggering...
Hello
I am starting with nRF 9160 DK and Segger Embedded Studio, I installed Segger through toolchain, the activation sim, updated of certificated and connect the DK to...
Hi everyone
Currently, I am working on a project related to the mesh network friendship feature on nrf52840. I am having the following problem: I have established a friendship...
I tried to debug UART communication between 52840 development board and 9160 development board. I sent 9 bytes of data from 52840 side, but I only received 8 bytes of data...
Hi,
I can't find how to get data received by interruption of UART. I've used libuarte example and I tried to get data from buffer buf in uart_event_handler, but it doesn...
I can see that other people have run into the "no code for breakpoint" problem when attempting to use the SEGGER debugger. I have read the earlier posts. I have not been able...
Dear Sir/Madam,
Can you please help to check and advise if both part# nRF52840-Dongle and nRF52840-DK have KC certificate? Thanks.
Best Regards,
Dan Lee
Hi,
I'm using for awhile TIMER0 and I want him completely disable.
I'm setting a TASKS STOP to stop a timer, clearing a interrupt and disabling interrupt in NVIC, but...
I'm looking at the datasheet for the NRF52832 because I'll be using it with a Raytac module and I'd like to know for sure how the SPI pins are set.
I see in the datasheet...
hi, i've used the official zephyr version till some days ago. the reset pin worked. now i've switched to the zephyr version "supported" by nordic and the pin reset isn't working...
I did the multilink central function when I used zephyr OS Connecting the five peripherals is stable at first, but after a while the error of <err> bt_att: ATT Timeout will...
