Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am trying to use APP_TIMER to detect if a sensor isn't responding to I2C Commands. I created and started the timer with the following steps. The project is based...
I'm using an ISP1807 at 1.8v in a very space constrained and power constrained device.
Is it ok to connect unused pins to GND to make routing easier?
Pins 3, 5, 8, 10...
H,
I am using the SDK 15.0.0 and Segger Embedded Studio for ARM V3.40.
I have been successfully defining a flash memory section for data exchange between the bootloader...
Hi,
I would like to enable the RAI support in the latest master branch of nRF.
Therefore I had a look at the kconfig reference:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
In my current project I have two type of boards. Some have the external 32kHz crystal mounted and some not.
I am trying to detect the presence of the external crystal...
I am looking at using SRP in our application and I am looking through "nrfxlib/crypto/nrf_cc310_mbedcrypto/include/mbedtls_extra/mbedtls_cc_srp.h".
There is a parameter...
Hi. I think I did a huge error by uploading the soft device S140 after erasing all.
Which lead to the device being locked. I tried to use J-link GDB Server still the issue...
Hello! I have a question about the work of nRF52 with memory, why does it work so crookedly? The first situation. We have a static void nus_data_handler (ble_nus_evt_t * p_evt...
I'm facing an issue with the build failing when using the gcc-arm-none-eabi-9-2019-q4-major toolchain on Windows 10. I saw a similar post here, github.com/.../22060 , but...
Hi,
I am struggling to get my WS2812 LEDs to work with my current setup. I am aware that I need logic level shifters, but Im still not sure if my hardware or software is...
Hello,
In our project, we have a BMD-300 module, which contains a nRF52832 chip, and a nRF52840DK. The BMD-300 module is used as peripheral and the nRF52840DK is used as...
Hi!
I would like to send and receive IEEE 802.15.4 compliant packages in a very simple way (no ACK, no routing, just raw data transmitted). For the simplicity of the task...
Hi,
i am using sdk 16 , nrf52832 .Merged with two sensors , i am storing it all in an array
example
uint16_t array[7];
array[0]=67; array[1]=90; array[2]={90}; .so...
