Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
In the v16.0.0 SDK the settings struct size is 904 bytes, but in the nrfutil it's 803 (screenshots attached). I figured the settings in python don't include peer_data(64bytes...
I was in the process of integrating a NAND flash to my project. - MX35LFxGE4AB
Initially, I thought it would be good idea to use QSPI, but it seems to only support NOR flash...
Hi
Im struggling to use the ble_app_template_cpp within SDKv16. I am using the nrf52840 DK (PCA10056) and want to us the S140 SoftDevice. The example isn't built for either...
Hello everyone:
The problem is still not resolved
Test broad is PCA10056
Test code was modified by \SDK17.0\examples\peripheral\usbd_msc\pca10056\blank\ses
Try to...
I am using a thingy52 device and in that, added code of advertising and scanning from the sdk 16. Advertising is run successfully. But getting packet loss issue. So, I am...
Hi
Im developing an application that will wake up on RTC every 15 minutes. My issue is that when using idle_state_handle, which in turn calls sd_ble_app_wait, the RTC...
Hi,
Trying to figure out the current requirement on GPIO input, can you point me in the correct direction in how to figure out how much input current the GPIO on nrf9160...
Hi,
we are planning to add a 256 MByte NAND flash to our sensor project. I saw the example for NOR flash on the PCA10056 which is working fine. But due to costs we want...
Hi,I am using the nRF52840 development board, S140 and SDK16.0, I have some questions about data transmission on the UART.
I am trying to make a central device that is similar...
Hi,
I am working on a custom nrf52840 board and am having trouble connecting to the usb interface on the chip. After testing with the dev kit, the adafruit bootloader...
I trying to establish communications with a (non Nordic) beaconed 802.15.4 coordinator.
I've used some code from the wireless_uart_raw example but did not use the FSM. ...
Hello all,
I am having a problem to get SAADC to work with low power. I am using custom board with chip NRF52811, SDK 16.0.0.
I had turned on the SAADC_CONFIG_LP_MODE...
Hello Everyone,
I am using my custom board with nrf52832 SoC and developing my application firmware with sdk15.2 & softdevice v6.1.0.
In my application code, BLE scanning...
Hi,
We were trying out the LTE RX/TX test using the AT%XREFTEST command and undestood that for LTE RX testing ,an external signal generator is required. Is there any way...
Hello
I would like to know if there is a capability of a truly secured boot with the nRF53, starting with a secure bootloader in some locked or immutable memory - i.e. secure...
