Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have python 3.9 installed. I can downgrade if that is the issue. I'll probably try that while I wait.
If I try and install "pip install nrfutil" it will succeed, but it...
The "getting started" guide and setup for nRF5340 a bit complicated...
1. Do you have IAR project example for nRFF5340?
2. What tools and setup are must to run first example...
Hi,
We have bought a few Nordic Thingy52 and used in our lab teaching for a few years now. Since the last year, we noticed that we have to downgrade NodeJS version in order...
I'm coming at this from a background of ANT+ applications.
In ANT+ there are documents detailing the structure of the data that is received in the ANT+ datagram.
I've...
Windows 10 USB link. NRF connect 3.6. Followed recommended instruction on extracting firmware. Pressed switch 3 in middle of board on power up. Device showed up in window...
Hi,
I was performing a mesh DFU, using a nordic Demoboard with a serial mesh bootloader and starting DFU with nrfutil.
The DFU starts and works good (packages are sent...
I have a call to bt_scan_start after a device disconnects.
When the device connects again, I get this error:
ASSERTION FAIL [params->value] @ WEST_TOPDIR/zephyr/subsys...
I am using the nRF Connect 3.6.0 Bluetooth Low Energy app v2.4.2 on MacOS. When I pair and bond with my device it works fine. I can disconnect and connect in the same session...
Hi
I am using nrf9160 device and in my application and have to use mathematical logarithm function in my application.
Could you please help me how I can use mathematical...
Hi!
I am trying to test the CLI over BLE example. I want to use it in another application for logging data to a laptop console over BLE.
However, I am having trouble following...
Hi,
We are using NRF52832 MCU for one of our BLE based project.
We are running out of memory when specific operation performed. Buffer crashed.
What is minimum setting...
I was using log to print debugging information when the BLE_GATTS_CFG_ATTR_TAB_SIZE message popped up. It doesn't normally happen. What's the reason for that? Thank you very...
After flashing the nRF-9160-DK with the required firmware ( as instructed in this video https://www.youtube.com/watch?v=rMvW3HXLErk&feature=youtu.be ), the LED 3 is flashing...
