Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am trying to integrate cli over Nordic UART Service. i want nus control over command line interface such as PuTTY or Termite.
How to solve this and what files should be...
I have two NRF52832 boards. I cannot get the SDK to compile so I'm going at it barebones style.
Transmitter Board code:
Receiver Board code:
The receiver board never...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
I use nrfjprog in a CI system (on Windows 10) which has multiple NRF52 boards attached to it. The boards are all run in parallel with the -s parameter to nrfjprog and the...
Hello, i have an issue with softdevice API combined with timeslot API. I use timeslot API to scan for packets one time (one time interval) with 30000us. Then before timeslot...
Hi, I'm using mqtt_simple example based application to send BLE tracking data through LTE on custom boards. UART is used for connection between MCUs. Power is ON constantly...
Hi all! Since I do not have a system for updating the certificate when changing the server, I decided to disable certificate verification when connecting to the https server...
Hi.
I am a student studying esb examples with nrf52433 board.
1. If data is sent from ptx to prx using static payload, is tx completed without receiving ACK? Don't need...
Hello,
I try to measure the current of the nRF SoC on my NRF52-DK, by using an oscilloscope and USB as a power supply, related to the guide from Nordic from here:
https...
Hi,
I need to write a 32-bit value to an NVM flash page whenever my code hits an assert failure. This failure can occur anywhere in the code - my application, the Nordic...
Hello,
I'm working on a circuit which has a pin connected to a pull-up resistor, using the nRF52 DK and SEGGER Embedded Studio 5.20 to develop the software.
This pin is...
Hello everybody, I am using Zephyr with the nrf52840-dk device. I would like to store the DTLS credentials with a secure way. I don't want to be part of the code and thus...
I have been testing out HTTPS with the http_application_update .
I have been able to successfully setup a TLS 1.2 connection, but I was seeing a lot of "Peer closed connection...
Hello
I would like to modify my Transmission Parameters of my Thread network. According to the CoAP protocol ( https://tools.ietf.org/html/rfc7252#section-4.8 ), it is possible...
Hi Dev Team,
I am trying to measure the low power performance of the nrf9160.
For this, I tried to use the "system_off" example in the folder : C:\Users\adeel\ncs\v1.4...
