Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
1) I ported UART into my code and it...
Hey all,
I would like to make a flexible design with ability to assemble NRF52832 or NRF52810 , both are pin to pin compatible ,
But i just wonder how to consider regulation...
Hello,
I am developing a capacitive sensing application with the nRF52 DK and Segger Embedded Studio. So far I have integrated the Capacitive Sensor Library Example into...
Hi everyone,
I am working on a project with the NRF9160 DK where I want to use the UART3 channel.
The issue is that I got compiling errors when I add CONFIG_UART_3_NRF_UARTE...
Hello,
I want to test the Thingy Mesh Provisioning Demo v0.7 with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo...
Hi,
I am using s140 v7.0.1 for nRF52840.
I found if I configure NRF_GPIOTE->CONFIG[0], then BLE will not work.
Which GPIOTE channels are used in s140?
Thank you.
Hello,
I need example code or guidance in how to receive eddystone advetising packets on the nRF52832.
In my project, I can send standard eddystone packets to a app...
Hi All,
I am new to BLE technology and I am working on nRF52840 and I have below queries.
1) I need to operate my device to scan and advertise both at the same time when...
I stuck a breakpoint in the main loop to capture the timer values. Everything looks good, the capture has worked. The interrupt isn't called however. I've disabled the softdevice...
Please understand my low English level.
Segger cannot find be_advdata.h. I've added this route to the preprocessor. But an error occurs. How can I fix this?
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
For better clarity, I am trying to understand...
When scanning, is there a built-in way to detect and ignore duplicate advertisement packets (i.e. from the same device)? Specifically, I want to instruct the SoftDevice not...
Hi.
Thank you for your hard work.
I would like to apply the Timer example to the Uart example in SDK 15.2.0.
It was able to build without any problems before the timer...
Can somebody help me to setting up debugging in eclipse (nRF52840_xxAA)? As all I use some old tutorial here . But I still can't set up debugging on eclipse for 3 years of...
