Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
i've made a custom shield plugged into the thingy: 52.
There is a tag connect connector on it. I have short SWD signal from thingy debug connector.
When i try...
Hey,
Is it not possible to use any Bluetooth status codes for disconnection when calling sd_ble_gap_disconnect ?
for example this is not working (I do not actually disconnect...
Hi,
Similar as this issue
Our QA team found the nRF9160 device will hang when user pull out the USIM card then try to deactivate LTE.
The issue can be repoduced by following...
We tested this issue on serial_lte_modem sample on NCS 1.2 and modem mfw_nrf9160_1.2.0
1, Enable CSCON unsolicited report:
AT+CSCON=2
2, Activate LTE search and connect...
Hi,
My problem in shortly is when I have debugger connected to nRF5282, I always get hardfault after some time.
https://i.ibb.co/hZ3bZ1b/optionbytes-1.png
I tried...
hi .i use the pca10056 connect to th nrfconnect by usb .andr dun the app Bluetooth low energy.other 52840 device run the hex of \nordic
sdk\nRF5_SDK_16.0.0_98a08e2\examples...
Hello,
I'am working with a project and want to maximize ble throughput from ble thingy52 to a central device. I have used the ble sniffer with wireshark to see data transfer...
Hi Team,
i am working on serial LTE modem sample project trying to send at commands through serial lte link monitor, found that device is not responding to at commands...
Hi,
Recently I updated nRF Toolbox iOS to 5.0.1.
I'm mainly using this tool for writing application via DFU to nRF51822 board.
I was using .hex files for DFU but I can...
Hi,
I am working on a product based on an nRF52832 (SDK 15.3, Softdevice S112 v6.1).
For security purposes, I would like to restrict the pairing / bonding procedure to...
Hello, guys!
I am using master branch of nRF Connect SDK and want to use UART_1 module of nRF9160 SiP to communicate with external devices.
I used nrf9160_pca10090ns.overlay...
Hello, I am evaluating different printed antenna options for my Nordic design using nRF52 series ICs. The small size of the meandered antenna used in the nRF24LU1 USB dongle...
Hi,
I am on SDK 15.2 and NRF52832. I think that I am quite stupid because I do not succeed to be in Non-scannable non-connectable mode.
I tried few stuffs, change directly...
Hello,
I need to create an acl connection using bd_address and GATT client LE connection mode.
how to create ACL connection?
How to close ACL connection using connection...
