Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have developed an bootloader operating with external flash for image storage. For the use case it is not acceptable to put the device into an inoperable (no-application...
Hello,
I've been looking at this post devzone.nordicsemi.com/.../ in regards to characteristic lengths.
I'm still not clear on the matter. Currently I have initialized...
Hi, I'm confused how to do fota of mcuboot on the nrf9160.
The source code is public on github in this branch: https://github.com/ExploratoryEngineering/nrf9160-telenor...
I just installed NRF Connect on an Archlinux via the AUR , but I cannot install any app. I even upgraded the package to 3.3.3, but I always get:
Error
Unable to...
Environment: nrf9160DK v0.8.2 nRF Connect SDK v1.2.0 Modem firmware: v1.2.0 Toolchain: gcc-arm-none-eabi-9-2019-q4-major-win32 I started with the nrf mqtt_simple sample and...
Hi,
I have bought TMP117 with NRF52832 from Nordic, a wristband becon module. I am new to this boards. I want to create my own Android app. I want to know how to do this...
Helllo,
i'm using a custom shield with the Thingy:52.
I need to control some TWI chips, but these chips (ADG728) have only one register.
I have done a specific driver...
In the nRF5 SDK v15.0.0 there is an example for beacon. (in my case ble_app_beacon_pca10040_s132)
This example works fine and acts as a non-connectable unidirected beacon...
Hi, I'm trying to add Characteristic User Description 0x2901 and CCCD 0x2902 to a characteristic. It seems 0x2902 always comes before 0x2901 in attribute table. Is there any...
Hello,
As per your sugesstion opened a new ticket in reference to existing ticket,
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with...
Hi,
I'm using nrf52-pca10040 and sdk-15.3, I tested an eeprom chip following twi_scanner example, using no block nrf_drv_twi_xfer way, which works well, then I put it in...
Hello,
I followed this tutorial and github example in order to make a custom service with the characteristics I need. However, I am running into an issue where the board...
Hi.
I am using nRF52840 Dongle. A problem occurred while merging the PIN_CHANGE_INT examples based on the BLE_APP_BEACON example. I connected the external button to the...
In the products that I am developing we use advertising packets in the scan response to pass some data around our devices. We wanted a way for the app we've made for iOS to...
Hi,
I am using nRF52840, S140 7.0.1. I am using ble_app_blinky application.
I am writing data into FDS records. After writing FDS, if I load new hex file using nrfjprog...
