Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi, I have a set up consisting of an nRF52840 and Raspberry Pi communicating over IPSP following the zephyr OS sample docs.zephyrproject.org/.../README.html My application...
Hi,
I've been using XMONITOR command to check some radio parameters. ATM, I am checking those once/minute, right before requesting power save mode from modem. After updating...
Hello,
I wondering if I use the nrf5_SDK_for_Mesh_v4.2.0_src light switch example and modify it to suit my needs.
Q1. I want set up a proxy node using nRF52832 so that...
Hi,
in https://devzone.nordicsemi.com/f/nordic-q-a/24115/io-pin-signal-during-reset it is mentioned that the pins of the nRF52832 get set to input _during_ a reset.
...
This is my RTC init function. Whenever I start advertising in fast-advertising mode, and timeout for fast advertising expires, the RTC2 timer stops running and COUNTER resets...
Hello,
I am trying to make a simple power optimized BLE peripheral device based on nRF52840.
Here is the chart from the Power Profiler
The device advertises once in...
Hello,
I am trying to use "west" command in Eclipse but I am not able to do it.
I was able to do that in Visual Studio though.
I found this link https://devzone.nordicsemi...
Hi,
We are trying to configure the WDT and are running into issues. The plan was have a timeout of 30 seconds when running and then 24 hours when sleeping. Note we are...
While developing the power supply for edge cases of NRF9160-SIBA we encountered problems with both the continuous and peak current consumption, mostly during startup. We are...
I have a question on stack guard that I tried to enable on nRF52840 and hope you can give me some pointer to verify it is functioning properly.
Basically, I call nrf_stack_guard_init...
Hello i am making an application using hid over gatt. i changed original keyboard usb description with fido description for test, however, i don't get any event through. I...
the link i given below tells, how to make a haptic glove using arduino mega
https://hackaday.io/project/160405-diy-haptic-glove-for-vr
i want to do it with nrf52840 DK...
Hi everyone,
I'm working on programming nRF52833. I want to my nRF52833 is able to broadcast advertising and also scanning (In another word, my device plays peripheral role...
Hi
I have upgraded from an early version of SLM to the latest version in nRF Connect SDK ver. 1.3.1
the SLM application is running on a custom board with a nRF52840. Using...
I found this application very useful!!
The code is now at the Github.
I found there are some problems to reconnect - it gets many errors and the peripherals eventually...
