I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Good afternoon,
I want to get date and time from the RTC1 and working on the S110.
As the RTC1 counter is just 24-bit long, final counter value (overflow) has to be taken...
Anyone had any success get uCXpresso.NRF working with the latest nRF51 Dongle. I can't seem to get the BLE stack working.
Trying to run this example but the device is not...
Just starting the external LFCLK needs a considerable amount of energy. With my evaluation board it takes about 340ms for the XTAL to get started, which is well within the...
I am only interested in one max bonded device at the moment so I want to replace the old bond with a new bond. Is there an easy way to do this? I only want to replace the...
Hi,
I am try to manage situation when a wrong PIN code is provided from Master control Panel.
Using an NRF51822 with S110 I receive this code:
BLE_GAP_SEC_STATUS_CONFIRM_VALUE...
Hi,
I'm trying to communicate between a stm32f4 (spi master) and a nrf51822 (spi slave). I have configured the MISO, MOSI, CS and SCLK of the nrf. I use the spi_slave_example...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1
My application has no display, and a single button for input. I want to prevent bonding until the button is pressed...
I use Eclipse, gcc and OS X to compile.
I had FW working just fine with SD 6 and SDK 5.2. I recently tried to upgrade and ran into many problems, but the latest is the...
Hi
I've written an application that uses the gazell proprietary stack for nrf51822 and I want to use OTA-DFU using BLE.
Is it possible to upload the new firmware using...
I’m running into a problem with the SoftDevice safe twi that’s been posted in the forums a few times. I got the file here:
devzone.nordicsemi.com/.../
One of my peripherals...
Hello,
I have been messing around with a PCA10001 Dev board trying to do some power consumption tests (Beacon demo code). When I enable RTC1 only and use __WFE in the main...
Hello everyone,
I haven't read anything in the official documentation about it, but I was wondering if the S110 has an embedded checksum that I can use to verify its integrity...
