Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello!
I have the NRF9160 DK set up to use UART2 and listen to AT commands from external MCU, NRF52840 DK configured to send using UART0.
The NRF9160 set up is done, pins...
I want to transfer 1000Bytes. if I transfer 1000bytes every second after some time connection broken,
and need to reboot the device and connect it again
how can I solve...
Hi, I get my first experiences with nRF905 modules (module DAYCOM M-FM-NR905 including spring antenna from Pollin) connected to ARDUINO DUEs. SPI communication works fine...
I'm designing a two layer board. I need to route the power supply to several parts while avoiding cutting up the ground plane. I'm consider running the power line on the opposite...
Hello
I'm trying to control the neopixeled WS2812. I referred to the following site.
https://electronut.in/nrf52-i2s-ws2812/
I'm going to use this example of neopixel...
Hi!
I'm developing serial communication programming on nRF52840 DK to get the UARTE1 communication on SDK 12.0.2.
I want to use app_uart_put or NRF_LOG_INFO function via...
I want to develop a device which can communicate with other users without any cellular coverage or network by creating a lora mesh network like above mentioned picture. in...
Hello,
I am having issues integrating mesh functionality into a preexisting BLE project.
My project is based around an nRF53832, with SoftDevice S132 and uses nRF5_SDK_17...
Hi,
i want to connect my nrf5340pdk board with the MPU6050 sensor. They should be communication using I2C.
I read different information about the connection of the sensor...
Hi,
I have two questions about the nRF52DK power consumption when powered via USB .. one is for interest, but the other one appears to be an issue.
I have run some comparative...
Hi, I found an unexpected bug which leads to stuck at this point 856419>, app_error_weak.c, 105, Mesh assert at 0x0003AA3A (:0) it's happened after a fast setting the level...
Hello,
I am trying to spot a bug in which some memory corruption is happening. I don't know in advance at which address the corruption will happen, as it happens in some...
I want to trigger SAADC samples manually, when a certain BLE message arrives. I'd ideally like to have a trigger scan 4 individual channels.
I see two function calls, though...
I want to use the SoftDevice APIs to read and write flash on the nRF51822. Are there any examples of how to do this. I see all kinds of mixes between pstorage, NVIC (not sure...
Hello,
I am new to Nordic and quite new to ZigBee. Just had a short evaluation with Silabs so far.
My goal is developing a custom lamp for serial production that needs...
