I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi
I start in programming on nrf9160 DK with a sensor BME280. I followed the tutorial "getting started part 2" (https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Hello, dear sir:
In my opinion, HFXO means external oscillator, I need to buy a external oscillator because it is not exist in nRF9160?
HFINT means internal oscillator...
I use sdk16 on nrf52810 for development, but I want to use long broadcast packageada. What should I do?
A short broadcast packet can only be 31 bytes
thank you!
To the kind attention of Nordic support team,
I was reading in peer_manager library that when a ble connection is established, using the connection handler as a parameter...
Hi ,
In our actual design, we are using nrf52810. We have done all our development on nrf52832, as there is no Eval Kit present for nrf52810. We are porting our development...
Hello,
I can see RTC drift of around 14 seconds in 1 hr when I select the internal RC oscillator in sdk-config of nrf-calender example.
Is this much drift expected? In...
I would like to add events for button release and button long push to my application. I also want to keep the SDK folder unmodified for easy upgrades.
To do this I copied...
Hi,
In my project, I am using High voltage mode [VDDH] in this case automatically REG1 [LDO] will be enabled. But my question is as per the datasheet i understood that even...
Hi.
I am developing using nRF52820 example source using SDK 17.0.2.
USB and LESC were added using S112.
However, during operation, the following HardFault error occurs...
Hi everyone,
I am trying to integrate the DFU service into my application on order to achieve buttonless OTA DFU but I am not able to implement it so far and I need your...
Hello,
I merged the two projects usbd_cdc_acm_pca10056 (A) and ble_app_hids_mouse_pca10056_s140 (B) by copying all additional contents from A's flash_placement.xml into...
Hello,
I am trying to send data obtained from a SAADC port via BLE using the ble_nus_data_send function. This must happen periodically at frequencies within the Gigahertz...
As we know, NRF9160 supports NB network and has an IMEI number itself. Now I want to know whether I can manage this IMEI number, such as reading, writing or modifying. In...
HI all,I am looking for a help.how to start SPIM RX task immediately delay less than 2us？
I have a SPIM test on 52832 DK board(QFAAE0) with SDK16.0, the MISO pin has connected...
Hello
I have a question about the Bluetooth multipairing function using nrf52832. How do I use this feature? And up to how many connections can I make?
Thank you!
