I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
I am a student studying zigbee. We succeeded in turning on/off the LEDs of zc_light using examples of zc_light and zc_switch. The question here is, where do you send and receive...
I am trying to duplicate a RF remote control which uses a Nrf24L01+ IC.
I have temporarily connect the SPI interface of my test chip to the SPI pins on the remote, and transmitted...
Hello guys,
I have already created the JSON file and checked it using the online JSON validator and viewer. Now, I am interested to figure out is it possible to use this...
I'm trying to pair my peripheral with the central using BLE.
In the central code (running on windows c#):
In the peripheral terminal:
the device in sending PM_EVT_CONN_SEC_PARAMS_REQ...
Hello,
I'm experiencing a disconnection problem on several BLE Mesh networks. My topology is 1 client with an average of 60 servers, for all networks. Client is connected...
Hi guys,
I have the same issue as coca1989 had 2 years ago . Did anybody found a solution?
I am using health model and simple message model. Client and Provisioner are...
Hi,
Iam working on a project based on Ble Mesh, Iam using nrf5_SDK_for_Mesh_v4.2.0_src. Iam trying to form a BLE Mesh network and control the light bulb. I went through...
Hello Devs,
I am facing an difficult time to write a custom opcode to a QSPI flash memory. where I am trying to read the manufacture ID, it requires send the OP code + Address...
Hi, We are looking for a Suitable wireless technology for Video transfer(Video Transmitter and receiver)
Main Constraint: - From Power Up-->Boot-Up time of Wireless transmitter...
Hello,
We are looking for a 2.4Ghz supported module with Programmable Frequency Deviation. Is there a product that we can consider from Nordic Semiconductor for this?...
Hi, We are working with integrating LoRa to our nRF52840 with BLE and FreeRTOS. To be sure that LoRa worked as expected, we configured and tested LoRa on nRF52840 dk and observed...
Hello,
I'm using nrf52840 and i would like to ask if it possible to use the I2C bus without external pullups. I mean, i would like to avoid using external pullups
is there...
I am using a NRF52840 DK with a SoftDevice S140 6.1.1. I have also flashed the secure ble bootloader on the device.
I have been using the nrfprog command line tools within...
Hello,
Got the MQTT_SIMPLE to work and the sensor samples from zephyr also, however, how can i mix the 2 to have the mqttsimple with some gpio and i2c sensor ? how will...
