Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
In the documentation of the nRF SDK for Mesh v4.1.0 is written: "The following figure demonstrates how the data packets flow between mesh nodes and their layers within the...
Hello
Beacon using timeslot API
I am trying to implementing a beacon functionality using your timeslot API.
The beacon shall run in parallel to the normal SoftDevice...
Hi all,
In our application we have a piconet master (acting as GATT client) and several piconet slaves (acting as GATT servers). We have only limited time on the channel...
Hello,
I've asked this question already at StackOverflow, and while I try Wireshark I wanted to see if someone has experienced the same issue and/or can provide further...
I can scan beacons with Scanner. and can use NUS (ble_periperall\ble_app_uart ) to get connect with device.
My goal is to combine both application Have NUS Service to connect...
As most developers using Nordic's SoftDevice quickly find out, halting the processor (e.g. hitting a break point) results in a fault and requires a reboot. This makes debugging...
we want to use nRF52833 as BLE5.1 AOA/DOA locator,here are some questions about to how to use it:
How many antennas are needed for direction finding/positioning? Is 6...
Hi everyone,
I have added the Characteristic User Description in order to add a human-readable name for my characteristics. However, the name still appears in hex format...
Hi everyone,
I have created a vendor service that works fine. Now I want to create a second one. What is the most efficient approach for doing this?
For the first service...
I am following the Zigbee Device Upgrade OTA tutorial and have run into an issue flashing the server firmware using a j-link and Particle Xenon dev board.
Environment Details...
Hi all,
I seem to be having a problem with running nRF connect for desktop 3.3.1 on MacOS (10.15.3). After installing the package to the application folder, on launching...
Hi,
When configuring a GPIO as output with DRIVE set to D0S1, i.e. "Disconnect '0' standard '1'", what is the leakage current when GPIO is set to 0, i.e Disconnected?
...
Hello,
I'm porting from ST32L151 to NRF52840.
I want to use the HMAC SHA1 method, but I can't see the related function.
The nrf_crypto_hmac_init function seems to...
First of all I have to say that the experience of bringing up the nRF9160 has been one of the worst. Tools upon tools, dependencies upon dependencies. Makes it a nightmare...
