Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
We're trying to minimize power consumption on our custom nRF52840-based board and we have some questions about the behavior of HFINT and HFXO. The specification says this...
Hello,
I am currently evaluating concepts on how I can power my nRF52832-custom-board with a LiPo-battery, in order to get a good tradeoff between lifetime and form-factor...
HI Team,
We are using the nRF52840 DK for our development purpose. We have some issues with USB J2 connector and unable to connect the on board debugger. We have tried...
Please note about 9 days ago another user reported similar problem but is his case LED3 and LED4 were blinking. In my case after reset I see LED 3 blink and then about 30...
It had been working fine until just this moment.
Every time i turn it on, it works fine for few seconds and then the red led in the device turns on. I don't understand the...
Hi,
I'm developing for a 52833 using SDK_17.0.0 and S113_7.0.1.
I'm using the following code with the intention that when the RDY pin goes low, it will wake up the processor...
Hi! I'm currently using the nrF52840 DK to send numbers by BLE. I have 2 questions for you. 1. Can I send negative values? ex. -1, -2, -3 2. Can I send decimal values? ex...
Hi Nordic Support
I have been working to port a blinky variant project and have found previous threads useful for guidance. I'm working with Segger Embedded Studio and have...
Hello,
Is there a way to multicast messages from BLE client to multiple servers? I know mesh does the same job but we are exploring a possibility to do the same using standard...
hi,I am working with nrf52832 board. I want to send the multiple beacon at a time(same instance).
can you please suggest me at a a time how many beacon we can send out(exact...
Let me first show what parameters I am choosing for calculating the data rates :
Conn interval is 7.5ms and connection length ext is off meaning it wont extend the connection...
Hello,
Application crashes at " nrf_sdh_enable_request ()" without returning any error code. Execution up to this seems fine and I get RTT debug prints. I have also tried...
In a timeslot-based multi-protocol application running on an nRF52832 with Softdevice S132 7.0.1, at seemingly random points and very rarely I observe the softevice calling...
There is an error in your documentation here:
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.0/lib_bootloader_dfu_banks.html?cp=7_1_3_5_1_2_2#lib_bootloader_dfu_appdata...
Hi, I need to support both BLE update and serial update with sdk 17. Going through some past post, the idea is clear.
1) Start with DFU_BLE example project.
2) Add the...
