Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi Guys,
I have managed to get the BLE DFU demo service working fine (dual bank) on nRF51822 EK. I use a Linux Python program ( bitbucket.org/.../nrf51_dfu_linux) (with...
what is the detection speed, when the beacon
enters into a wall unit area? With their 868 beacon they can
detect in 0,2 seconds. Is the nRF51x22 in sleep mode and does it...
For our application, As I used 24LU1(host) with 51822(device) be the platform.
I hope to transmit Audio data with 8 kHz, 10 bits data format. To commit the requirements ...
Hi,
I have installed "mastercontrolpanel.3.4.0.8098.x86.msi" on my PC, I could not find my master dongle after runing it with my dongle be inserted in USB slot. The screen...
Hello all,
I am getting an error when my device disconnects from the client. The error occurs while bond storage due to data limit exceeds.
err_code = ble_bondmngr_bonded_centrals_store...
Hi all,
I have made some modifications to the bootloader example project (dfu_dual_bank_ble, s110) to get a bootloader that meets my requirements. It is working ok, I can...
I debugging some function abnormal after OTA problem, and problem with disappear after redo OTA FW upgrade, duirng it I found a problem about Master Control Panel FW upgrade...
From the datasheet, the On mode with all blocks idle draws 2.6 uA.
In my code for the PCA10001, I immediately set:
void sleep(void)
{
__SEV();
__WFE();
__WFE();...
I was going through online material all of which mention that the profiles and protocols (GAP,GATT,L2CAP) i.e. the host for a BLE implementation is a software stack rather...
Hello - I have gotten blinky_example up and running in eclipse using the SDK 5.2, nan-29, and some additional google-fu.
Now when I press debug and the play button, it...
I am trying to use nRF UART app and nRF8001 chip. But I cannot change the device name. I intend to change the device name after nRF UART app detects the device. Plus when...
I'm trying to create a method so a users can initiate an OTA update from a paired device. To that end I've written something which is supposed to invalidate the data at the...
I'd tried some first steps using nRF Sniffer on a linux host.
Within sniffer_uart_protocol.xlsx I read something about the Uart packet format et cetera.
I'd programmed...
I am trying to get ble_app_beacon exampel working on the PCA10001 on my nrf51822 working. However when I simply run and reach APP_ERROR_CHECK(err_code) inside "advertising_init...
