Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello,
After a long investigation I got to the conclusion that SPI master (spi3) has been broken in the SDK version 1.4.1.
It is working fine in V1.3.1
I have an application...
Hello,
I'm using SEGGER Embedded Studio 5.30a with NCS 1.4.99.
I'm trying the "hello_world" sample but when i want to run on the nRF5340DK i get the followings errors...
Hi,
I am using FDS for read and write the records with SDK17, My code is working fine but when I change the optimization level 2 for size then I am getting FDS_ERR_UNALIGNED_ADDR...
Hello everyone,
I'd like to perform a DFU through the USB port on my custom NRF9160 board (DFU over UART) using the NRF Connect Programmer App.
I already did the Firmware...
Hi,
I'm using NRF52840 to connect with a mobile device.
During the connection, I have random disconnection with the reason code BLE_HCI_REMOTE_USER_TERMINATED_CONNECTION...
Excuse me, I want to download the nRF52810 reference layout on official website, however I can't find it.
Could you please send a nRF52810 QCAA reference layout to me
When the nRF is connected as a peripheral and no data is transferred either direction except the empty packet every connection interval, does the power consumption increase...
Dear,
I tried to make a copy of the Asset Tracker example application to start my own project. i gett this error
create_nordic_project.py failed
Creating solution...
Hi I am using the latest SDK for Mesh and also the latest nrf sdk. Downloaded and installed both last week. I have written an application that is derived from the light_switch...
Folks,
We are working on a custom design where the STM32L4 (external host MCU) talks to the nRF9160 over an UART connection to transmit sensor data. When the sensor data...
Hi,
I'm use nrf52840 with Light switch example of nRF5 SDK for Mesh v5.0.0 . Could I modify the packet of network layer ?
I want to add 2 bytes of UUID in the packet...
Hi, I want to add compression libraries like lz4 and audio compression to my zephyr projects. I am struggling to find good guides on how to add external/third party libraries...
Hi,
I have a nrf52810 board working as a peripheral, I want my board to connect to specific central application to protect it with malicious attack by other devices.
Please...
An error occurs when you run the following program(main.c).
[1;33m<wrn> bt_hci_core: opcode 0x2006 status 0x01 [1;31m<err> LOG_MODULE_NAME: Advertising start (err -5)
...
In the nrfConnect SDK I can see just one example for a I2C sensor - BH1749
I want to modify this for other I2C sensors.
However the README does not explain how to make...
