Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
Hello,
I have a system composed of one central that needs to 1) briefly connect to many (100+) peripherals, 2) download a small amount of data from each, and then 3) disconnect...
Hello,
I am working with SDK 15.3.0 and the nRF 52832. I am working with the Segger IDE v4.16.
I attempted to load the scripting as instructed in the SDK documentation...
Hi, I had this working, I'm sure of it. Now though I get 100% duty on one channel and 0% on another. Something's not right. Pins are correct, my focus is CFG_PWM_OUTPUT_FRONT_NUM...
Best regards:
Once the data was received in PRX, Is there a way forward (or modify) to PTX the same data and deliver it together with ACK payload in the same transaction...
Hello, i would like to test usb_msc example on a custom board, and i have few questions:
- will this QSPI flash chip work with nRF52840 QSPI interface, and is it sufficient...
Hello,
I'm doing some clean up in my code and i wanted to use only nrfx library as it advised to do. Regarding the watchdog i have set in my app_config.g file (used by my...
Hi,
Right now i am working on mesh sdk 3.0.0 on segger embedded studio and board i am using nrf52832. In my application i am trying to implement the watchdog timer but it...
Hi,
I want to use the nRF52832 on a recording system for sending the data to computer using BLE. I want to receive data after a while that the system is put in its position...
Here is my function to generate random numbers of desired length.
After generating a few(5 to 6) random numbers the function hangs at .
I am using RIOT OS on nrf52832...
Hi.
Hope you are well.
I intend to use the nRF52832 for a wireless neural recording system and I need the nrf to do some works for me, such as:
1. putting the system...
i am using nRF52832 with Mesh3.0.0, i want to build a network like a chain,Client1 to Server2 to Server3 and Server4 with interval about 40 meters, however i tested with light...
Hello,
Our team are evaluating the nRF52833 vs the nRF52840 and would like to understand the following
1. The nRF52840 clearly state that its RNG hardware is NIST SP800...
Windows 10, Segger V4.52c, S132, SDK 15.2.0, nRF52832
I'm trying to add Peer Manger to the UART template. I included all the C files from a tutorial I found and enabled...
Hello.
I am using nrf52-dk with 52832 (PCA10040).
To check the current consumption, I made a simple test.
I need to wake up every 5 seconds, do what is needed and fall...
I am currently working on custom firmware hosted by the nrf52832 SoC on a custom PCB. The project is built with a makefile and armgcc, using the "nRF5_SDK_15.0.0_a53641a"...
