Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi Team
I am trying to implement the firmware upgrade for master controller nrf52832 on chip using esp8266 over uart and I am very new with this boot-loader part.
I...
Hi
I had implemented a DFU module in esp8266 where I am trying to upgrade nrf over serial (UART Communication).
I had success with Init file write but when I send the...
Hi,
I am using nrf52833 EVB as an SPI master. The data is sent properly and well-received at the slave, however, I have a problem with the data received.
The problem...
Behaviour:
- Bluefruit the feater (nRF82832)
- Bluetooth BLE
- Implementation of Fitness Machine Service (0x1826)
- What is correct : all characteristics notified...
Hello, Nordic!
Our project is at evaluation stage. We aimed to build an Bluetooth 5.1 AoA indoor locator system, where the reciever should know the location of the transmitter...
We are using nrf52840 USB dongle to get PIR sensor readings and send measurements over the Bluetooth Mesh Schematics are following: We increased power for peripherals to 3...
Hi:
When I use nRF51822's 2.4G Radio(not BLE),I want to improve anti-interference level,Make sure that all my pairs of host and device can communicate normally.
Thank...
Hi
Looking at the AGPS sample code, it seems GPS/LTE is turned on and off using AT commands (AT+CFUN=x, x in {20, 21, 31}).
Do you recommend NOT using PSM when using AGPS...
Hello,
I have several nrf52 Development Kits which will be used for creating a Bluetooth mesh network. They sport the NRF52832 SoC.
Do they have, or will ever have, support...
Hello
*Environment
- LG V30 (Android 9)
- nRF52832, 15.3.0 SDK, S132
- nRF5340 ( I can't find SDK version)
I have some issue.
LG V30 Mobile can't reconnect...
Hi,
I am using nRF52840 USB dongle and DFU trigger library to update firmware without push any button.
The Python 2.7.x is working fine for DFU trigger into the DFU mode...
Hi!
I am developing a iot solution and I wanna send sensors data to broker by MQTT publisher. In my code already has the W5100 development and now I want to connect my device...
Hello,
I would like to create a new box in the nRF cloud for recording additional data. I know these boxes allow exporting the recorded data into a CSV file, which is ultimately...
Hi,
I have the below queries regarding the power consumption and memory
1) If my device is connected to the mobile phone and if it is scanning and the same it is advertising...
I'm trying to develop a code for the nrf52840 with a BLE link as Peripheral and Server (common configuration, but no SDK example). I start with a GATT server and changing...
