The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi community ! Here : https://devzone.nordicsemi.com/f/nordic-q-a/62414/different-behaviour-with-same-program-and-boards i get some problem with different behaviour when programming...
I'm using the Laird Connectivity BL654-DVK board as a basis for evaluating the nRF52840 for our application.
I started by using the .../examples/ble_peripheral/ble_app_hrs_freertos...
Hi,
When we do the UART stress testing with serial_lte_modem sample, the slm will crash by sending AT commands with interval 100ms.
the debug log will show "<wrn> at_host...
Hi ,
I have question about the specification of CPU running current. We did measure the current by PPK to force the CPU always running but the result is quite different...
Dear DevZone, I'm trying to perform a BLE OTA DFU with two nRF52840 Dev Kits. I followed the step by step guide from Nordic provided at the following link: devzone.nordicsemi...
Hi , Dear Nordic supports:
I am using NRF52832 for the iterative development of a product. In the previous generation of products, I used a PWM control LED flashing, whose...
Hello.
Could someone recommend me a verified antenna RF Switch for AoA using Bluetooth nrf52811 ?
What parameters are crucial for proper functionality with nrf52811? ...
Hi,
In ble_app_cts_c example(SDK 16), is it necessary to perform app_timer_init()? Because I could see that, no timers are being setup in the function timers_init().
If...
Hi,
When I read about interframe spacing in the product spec ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fradio.html&cp=4_0_0_5_19_8&anchor=ifs ...
I have a nrf52832 chip acting as a serial passthrough to an external app. Basically, it works great, unless I start sending high amounts of data into it. Once I do that, I...
I am developing an IoT system in which I need to link multiple devices to a master, which is why my nRF52810 chip caught my attention so I am interested in knowing how many...
The address range for Bootloader is from 0x0007 8000 - 0x0007 E000 for SDK 16 on nRF52832 device. See this link ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16...
Dear Sir,
Using SDK 16.0 for NRF52833. My application uses NRF FDS lib (flash data storage)
Immediate fds read after fds write gives 0. But after a board reset I get...
