Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
My firmware is using SDK 17.0.2, and it includes CPS, battery, and a custom service. Everything has been working fine. The custom service is responsible for sending and receiving...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
Hi,
The following URL does not include nRF54L15, is it supported?
https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/samples/openthread/coap_server/README.html
...
Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
Hello,
We are working on an NRF5340/NRF7002 based project with NCS 2.7.0 SDK. We have been able to get Amazon Root CA 1 and 3 working with the following .conf:
Now...
Hello,
I am working with the nRF7002 DK board and attempting to use the "Light Bulb Matter" example from Zephyr. I am encountering issues when trying to connect the board...
In the nRF5 SDK v15.0.0 there is an example for beacon. (in my case ble_app_beacon_pca10040_s132)
This example works fine and acts as a non-connectable unidirected beacon...
Hi, I'm trying to add Characteristic User Description 0x2901 and CCCD 0x2902 to a characteristic. It seems 0x2902 always comes before 0x2901 in attribute table. Is there any...
Hello,
As per your sugesstion opened a new ticket in reference to existing ticket,
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with...
Hi,
I'm using nrf52-pca10040 and sdk-15.3, I tested an eeprom chip following twi_scanner example, using no block nrf_drv_twi_xfer way, which works well, then I put it in...
Hello,
I followed this tutorial and github example in order to make a custom service with the characteristics I need. However, I am running into an issue where the board...
Hi.
I am using nRF52840 Dongle. A problem occurred while merging the PIN_CHANGE_INT examples based on the BLE_APP_BEACON example. I connected the external button to the...
In the products that I am developing we use advertising packets in the scan response to pass some data around our devices. We wanted a way for the app we've made for iOS to...
Hi,
I am using nRF52840, S140 7.0.1. I am using ble_app_blinky application.
I am writing data into FDS records. After writing FDS, if I load new hex file using nrfjprog...
Dear all,
I'm trying to go to SYSTEMOFF mode and then wake up from activity on UART rx pin (nrf51822).
If I do this:
nrf_uart_txrx_pins_set(NRF_UART0,NRF_UART_PSEL_DISCONNECTED...
Hello, I have a BLE peripheral, that should receive larger amounts of data using a l2cap channel. The central (a MacBook) creates the L2CAP channel, the channel is purely...
Hello,
we develop an open source framework that we are currently extending to also support the BLE Mesh Access Layer Models. We are currently implementing the foundation...
I am using nrf52810, using sdk15.2, softdevice6.1.0, my application flash takes up 56KB (I used fds), softdevice: 100KB and bootloader: 24KB, resulting in insufficient flash...
Hi,
I'm try to test my nRF52833DK using the nRF connect Direst Test Mode. Even if I flash the DTM binaries in nRF5 SDK 16, the Direct Test Mode app says something like ...
Dear Sir.
I am using SPI as follows.
gpio_pin_write(dev_io, LIS2DH12_CS_PIN, false); err = spi_transceive(spi_dev1, &spi_cfg1, &tx, &rx); gpio_pin_write(dev_io, LIS2DH12_CS_PIN...
The firmware is based on the BLE UART example running on an nRF52832 with the S132 softdevice. The first batch of boards were build with the QFABB0 chip revision of the nRF52832...
