I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hello,
I have made a project that was based on the nRF9151 Development Kit and it works great. I had to select the -ns configuration to get anything to ever build and now...
Hi,
I bought a new nrf52840 DK board as one ofthe original nrf board of my Qorvo QM33120WDK1 kit ( 2 x nrf52840 DK + QM33120W + QM33110W) J3 connector broke. Out of the...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Hi,
I'm trying to build a prototype using the Adafruit nRF8001 Breakout and an mbed ARM CPU.
After Reset, I get a Device Started Event, telling me the chip is in Setup...
Hi,
In SD100v8, there is capability of checking the application version, to make sure no downgrade (or any other criteria required). The reference is in Link to SDK
...
There is a blog post for advertising but none for connection interval.
I am wondering how big is the difference for this example:
Measurement on peripheral every 4 seconds...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hi,
Got stuck on an issue that has come and gone and then working fine, and are now back again.
I use a nrf51 module with the led-button-service example (sdk 5.2). It...
So, we are pretty far along in development (I have inherited the project) with an nrf51822, SDK 4.4.2 and SoftDevice "6.0.0-alpha". We are nearing release, and I was told...
I have set the POFCON to enable the power failure comparator and set the voltage level to2.5 volts. How do I know when the battery voltage is below the 2.5 volt level? How...
I want to try a UART communication without RTS & CTS
my board is PCA10001, and I use the SDK 6.1 example: uart_example.
I use Serial Port Utility to communicate with the...
Using SD_110 v6 I get a hardfault on the final call to sd_nvic_EnableIRQ(SWI2_IRQn);
sd_softdevice_enable before that returns success. Any idea why enabling interrupt could...
Hi,
I'm trying to implement an existing proprietary protocol on the nRF51422 SoC. In this protocol the device address is placed differently in the frame than the predefined...
I want to confirm with Nordic staff that the MBR compares the new bootloader with the one it will replace when executing SD_MBR_COMMAND_COPY_BL. It seems that after a comparison...
Hello
Just few quick questions. What happens to the S110 Softdevice after the APP_ADV_TIMEOUT_IN_SECONDS period?
I'm using the nRF51 DK and the ble UART example and I...
As I am using nRF51422 EK (Evaluation kit), would like to know how to test with BT2.5 or lower version. Is this has backward compatibility. As when I give option of FLAG other...
