I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I am trying to communicate with a SH1106 OLED display using TWI and the popular u8g2 display controller library.
I've verified that the display works without problems on...
I am currently development an app based on the example from the experimental folder using a NRF DK52 as a relay between a central and multiple peripherals.
The app should...
Hello,
Happy New Year.
I'm not able to find nRF52840-QIAA-T or any replacement of this SoC available in the North American market.
I need atleast 5 SoC of the...
Setup: nrf52840 (without internal dc/dc), VDD = 3.3V
Assuming the VDD rail ramps up slowly, the nrf52 will start booting at it's power-on reset threshold of 1.75V (POR)...
Dear BLE Experts, I've followed this tutorial to create a custom GATT service and characteristic. The tutorial seems to be based on the BLE SDK , not the MESH sdk, hence the...
Hello,
Our company is kicking off a project (while we are at the very beginning stage) where multiple nodes (up to 1K) should be connected within a mutual network. I wanted...
We are looking to increase battery life for a product that uses the nRF52832. I'm wondering if it's possible to provide 1.3V directly to the DEC4 pin rather than use the internal...
Hi, I'm referring to this post over 3 years ago: Nordic DevZone (nordicsemi.com)
I'm using Android 8.0, and I'm using SDK 12.3.0 for firmware. I'm trying to create bond...
Hi,
I noticed that when I initiate a chip-erase on the flash-chip and reset the MCU, I'm getting NRFX_ERROR_TIMEOUT's on my nrfx_qspi_init().
I found this ticket: https...
i am using nrf52840 DK with softdevice (s140_nrf52840_5.0.0-1.alpha_softdevice) and applying this throughput example ATT_MTU Throughput Example . and notice that when I use...
Hello I have a problem with the scanning of ble phy coded in Android, I need it to be continuous (or almost) but it seems that for coded it is not possible unlike with legacy...
There are more than one task, after completing the periodic work,the 52832 module should enter system on low power mode,sleep 30 minutes,then wake up and continue with the...
Hello:
I have set the scanning module to search devices by MAC address. It finds the devices that are using a Static Random address, but it cannot find the ones using a...
Hi,
in my project I have a custom board with a nRF52832 chip that reads SAADC data and transmits this data (peripheral role). This data is received by a nRF52840-DK board...
