I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
I combined SAADC into the ble_app_uart_c example and got error once it got to scan_start();
"ble_scan: sd_ble_gap_scan_start returned 0x9"
If I put the scan_start() in...
OOB can be used to assure physically that the device provisioned is the wanted one.
In my application the devices won't allow for OOB.
How can I ensure that only my...
Hi,
I used this user guide: https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf .
I am using the nRF52840 DK for the sniffer, and managed to connect it and...
I changed the IO of the SPI and could not receive the data.
Hardware: nrf52832 DK two
Software: nRF5_SDK_17.0.2_d674dde\examples\peripheral\spi and nRF5_SDK_17.0.2_d674dde...
Hi,
I'm developing an application for the nRF52840 that uses 3 SAADC channels. In particular, the channels are configured as below:
I'm able to get the samples from...
It is unclear, for both the Thingy 91, version 1.0.2, and nRF9160-DK, version 0.8.3, if they need bias-tee's for use with an external active GPS antenna. Also, what about...
Hello, I have problem and I hope you can help me.
I have 3 sensor nodes. every node has an IMU sensor and nRF52840 microcontroller. These nodes send the IMU data to the...
We bought 4 NRF5340 PDK and trying to setup BLE mesh. As suggested in the getting started guide, there are two BLE mesh example samples from nordic and zephyr. However, for...
My code uses the nrfx SPIM driver. This gives you the option to use interrupts or not. Interrupts are great for long message transfers, allowing sleep while waiting for the...
SDK 14.0 +nrf52832:
We use phone to send command to our toy(nrf52832) every 100ms to control a motor accurately，mostly toy received command is long than 100ms(more than...
Hi, Is it possible to order nRF5340 QKAAD0? This one is on DK and the last IC version? As I can see, your distributors e.g. Mouser only have nRF5340-QKAA-AB0-R/R7 but this...
Hi,
I am using nrf52832 development board with s132 softdevice and SDK17. I want to add the DFU service to this application so that I can update the firmware to the device...
Hi,
In the Enhanced Shockburst User Guide, there is a brief discussion about the required bit pattern of 1st on-air byte of the base radio address
(which immediately follows...
If I use nRF Connect to connect to the Peripheral and the Subscribe to Notification Characteristic I can see in the "Enabling notifications" in the log (however no notifications...
Hello
I use sdk v17.0 and nrf52832.
I'd like to use 1-channel PWM and 2-channel PWM. However, an error is output from the pwm_enable when using these two together.
...
