Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Our setup is using a NRF52832 with SDK15.0.0.
While working with a time sensitive external circuit where we both sample the state of the GPIO and enable LDETECT on it...
I have just received my nRF52 development board and I have tried to program one of the pre-bjui;t examples (Blinky). The USB drive on the board appears and if I drag the hex...
Hi,
I'm using an application with FreeRTOS , nRF52833, SDK 16.
When I'm trying to get it into low power (sleep mode) the system still consumes ~4mA
In vPortSuppressTicksAndSleep...
Hi,
I am starting with PPK. Tried some measurements on ble examples and looks like i am doing something wrong. I have aproximatelly 7mA during advertising. Am I doing something...
Hi,
i have load existing program to new nRF52 module. But it shows NRF_ERROR_NO_MEM.
Same old module doesn't show this error. i also reload the soft device. But no improvement...
I'm looking to implement the following security schema:
The peripheral does not have a display nor input capabilities
A smartphone will connect to the device
The peripheral...
I can use the nRF Sniffer to capture packets , but info "Empty PDU" is more and more, I want filter it. Please kindly help me how to operate it. Many thanks!
Hello. I have 3 peripherals connected to 1 central. The BLE_GAP_EVT_TIMEOUT event occurs in Central. Occurrence timing is random, p_ble_evt->evt.gap_evt.params.timeout.src...
Hi,
We are developing a solution with our partner company based on nrf52833 using S140 softdevice.
I would like to change the advertisement power after every advertisement...
I'm new to the nRF5340 and zephyr and ncs, but I have gone through the tutorial series https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts...
I'm trying to look at the nRF log for the temperature example I found in examples/peripherals using my nRF52840 development kit.
My laptop is windows and I have the DK plugged...
i am working with nrf52832
i need to check 2 analog inputs and set my own v- (ref)
i can have value read every few seconds so no fast readings needs to be done
if...
Hi, I'm currently evaluating using a nRF52810 based module to synchronize time between a number (2-20) of the same devices. I currently have a working prototype using an ESP32...
Hello,
I need to interface with a touch sensor from Azoteq (IQS263). This device allows a communication window during which you can read or write on I2C. The issue is that...
