I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
there is a module in the skylab project on the nRF52832 chip and it does not agree with the tablet, which is old BT. Is it possible, through the firmware or SDK, to downgrade...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
Hi,
I am learning how to write and read from flash memory on nRF52833 dev board for a BLE application.
I followed the heart rate example as shown in https://devzone.nordicsemi...
I am writing an application for the nRF52DK which uses two additional push buttons besides the 4 already present on the board.
Using GPIOTE the detection of the button press...
I have a working project that uses the NRF_LOG module to send debug outputs over the UART backend. When just using the logging module everything works correctly.
I added...
Hi,
Is it possible to set multiple APNs in nrf9160 and with fallbacks to next APN if one not working?
Suppose if we set 2 APNs at CID=0 and CID =1 positions using AT+CGDCONT...
Hello I am trying to execute the functions of SPIS and thread on nrf52840 Refer to his code to write nrf52840 SPIS: https://devzone.nordicsemi.com/f/nordic-q-a/68854/nrf5340...
Hi,
I am trying to configure the nRF Connect SDK on a Mac running Catalina for the first time and have followed the nRf Connect v3.6.0 - Getting Started Assistant.
I am...
I am new to the Segger Studio and nRF52840 . (However not a Newbie to Microprocessors)
Off the Bat :- Blinky example works fine...
.....however when I try to get the PWM_driver...
Hello, I wanted to know do this chip ( nRF52810) has both tag (beacon) and receiver function? If cannot is there any other Bluetooth chip suggestion? My main idea is to use...
I am new to Arm and Nordic devices and I am trying to port the Thingy52 firmware to SES so we can add some additional sensors.
I have got the Thingy52 firmware to compile...
Hi Nordic Community,
I follow the below link to create an openthread border router. I successfully send sensor data on things.io.
https://infocenter.nordicsemi.com/index...
