Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I've been working with the nRF52840 WLCSP package for a month or two now, and in many ways it's a great compact chip. However, as my projects require more and more pins, I...
Hi guys, Im now developing my custom board with nRF52832 based on the reference schematic below. And using Keil uvision for a programming my board.
The final objective of...
Hi
I have two custom build boards based on nRF9160-SICA. Both boards also have a nrf52840 running application code. The nr91's are running identical firmware (slightly modified...
Dear.
Now Im testing the nRF24L01 to develop a module.
Using this, I want to know the receive power.
nRF24L01 has a registef to use similar function. Register...
Hi,
I'm trying to write firmware for the nrf52840 that reads from a sensor and then sends data to a PC over BLE. Ultimately, I need the BLE link to achieve ~ 1.1 Mbps throughput...
Hi all,
I observe a connection supervision timeout (HMI error code 0x08) in my Nordic firmware with certain Android smartphones (controller).
Additional info regarding...
Hi. I'm just wondering if Nordic Semi engineers have done any tests with standard beacons (any particular beacon interval and test condition) application and compared current...
Hi teams,
We made BLE mesh custom boards based on nRF52833.
These nodes are configured to send broadcast messages for every 10 seconds.
Currently, these boards uses...
Hi Sir,
We would like to use the Radio test to do the basick TX/RX test in SDK 15.2
We use the nRF52840-DK for test and follow the CLI document .
1. We use two board...
Baud rate 460800, error code NRFX_ERROR_INTERNAL(1) occurred when the serial port received data。
I want to know how to avoid this problem, the current transfer rate is less...
Hi
We need the recv() be blocking until the full amount of requested data can be returned or the operation was timeout, how to achieve this?
I tried flag MSG_WAITALL but...
Hi. Can anyone think of a way to use the nRF52832 (probably Timer) to detect approximately 125KHz-150KHz variable square wave down to about a 1Hz resolution? I'd like to detect...
Is there any example for Directed Advertising? I'll design my NUS central and peripheral use Directed Advertising, because I would like to have other bluetooth devices connected...
I use this code below mentioned in this question https://devzone.nordicsemi.com/f/nordic-q-a/26030/how-to-reach-nrf52840-uarte-current-supply-specification
This can reduce...
