The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hello,
I have one SPI instance (instance 3, but have tried others) reading data from an ADC. It's reading data from an ADC triggered by a DRDY signal at 25khz. I setup a...
Hi,
I just enabled the CONFIG_BOOTLOADER_MCUBOOT=y for serial LTE modem application to understand the flash partitions and to perform the serial DFU(not sure if its really...
Hallo, using nRF52840 DK with Keil uVision 5.30, I try to debug the example ble_app_uart in the folder ble_peripheral, pca10056, s140. Compilation is OK, erase/programming...
please help me
I was working with LPCOMP when I set up lpcomp like above, even though I have set my comparator but just impacting anything on the AIN2 pin...
Hi,
I am using nrf52832 mesh board.I want to unprovision the device by pressing the button on the board.In the lc server example they handled it in rtt as it dont have hal...
Hello everyone, I am Smit and I am an IOS developer.
I am stuck to write data into the BLE device. Can anyone please help me out with this? Can anyone tell me how to do...
Hi,
I used the command line to install the toolchains as follows:
sudo apt install gcc-arm-none-eabi
It then installed version 9.3.1 of the tools on my Linux ubuntu...
Hi,
We have implemented a custom Watchdog Timeout handler, where we do the stack-dump. It has worked fine and we were able to analyze and fix the Watchdog resets. But...
Hi,
We are using some nRF52 DKs for debugging and programming prototype boards. Everything went fine until we wanted to expand our testing setup and got some new nRF52...
Hello team, I want to use Normal Sleep mode that is (__WFE) normal sleep mode in NRF51822 using MBED OS 2. But, when ever I am using this method, my code has been waiting...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
The following vulnerability "CVE-2020-10135" has been reported by the Bluetooth SIG. Will this device be affected...
Hello
I am using SDK v17 and sending the value of acceleration sensor to the app.
I want to use this value to process some action in the app. For example, if the transmitted...
Hello Nordic Community,
I've stumble upon an issue with a characteristic configured to not require authorization but still does on certain occasions.
Consider a service...
