The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I tested the example of MQTT publisher of the IOT SDK and it works, and for the next step i want my mqtt publisher scan for the router, in the example it is advertising and...
Hi Nordic
I am working on the SAADC example and I have noticed that when the buffer is filled the NRFX_SAADC_EVT_DONE event is generated. My question is on NRF_SAADC_INT_DONE...
Hello I am seeing some excessive current consumption (~650uA) when connected and do not know where it is coming from. I am using a custom board with an external 32 MHz crystal...
Hello,
At the moment, there is a need to develop an application for Android to communicate with our device. And we encountered the following difficulties: using the standard...
Good day.
We have a customer that asked us the following questions about the nRF9160 asset tracker application and we're hoping that you can help.
1. What tools are...
Today i received my brand new 2 pieces of nrf51-dks. when i wanted to try out some of the examples, i tried to copy over the .hex file to the usb drive, but for some reason...
Dear experts
We have no experience using Nordic SOC neither Nordic SDK, but want to start the contact with the platform.
Our aim is to get knowledge, setup the development...
Hi,
Can I use the serial interface to interact with an nRF52840 dongle running a mesh stack?
If so is this limited to UART or can the USB connectivity be used?
If any...
Hi,
I am developing a device based on NRF52840 soc in ble central mode. Could I claim when I do not call sd_ble_gap_scan_start function BLE radio is thoroughly OFF and there...
Hi everyone,
Maybe this is a very simple question but I want to avoid future troubles, that's why I'm asking. I want to copy an example from SDK16 and rename it. For example...
My Win 10 is up to date. Seger' J-Link driver is OK. Here's message from log screen: Please help to find what I missed. Thanks.
08:03:35.048
Using nrfjprog library 10...
Hello,
I am currently trying to use the MQTT publisher example to send a message to a locally hosted MQTT broker (I assume I can use a local IPv6 address?). The MQTT broker...
Hey Nordic Team,
I'm in the midst of integration the nRF91. As with the nRF52 designs, less work was taken out of the RF design aspect because it has a built in balun. As...
Hi Nordic：
I burned the AP & Modem firmware in the picture below, and found that the current consumption when entering PSM is 500μA. Please help to analyze. What caused...
Hello ,
I am using freertos with nrf uart service, i could able to get these timings that seem little bit weird.
one of the pin toggled for each successful ble_nus_data_send...
