Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
I am trying to get the nRF-IEEE-802.15.4-radio-driver found at GitHub to run on my nRF52840 DK.
Does anyone have a check list or can explain how to link the files...
Hello,
I'm wanting to start a project with the NRF52840 DK in Segger Embedded Studio. I went through almost all of the tutorials and set up the SDK.... etc but I have...
hello.
I used 52840 act as center device.whose RX TX connected to my another MCU(MTK7688 UART). This is a IoT-GateWay. now I want to upgrade the 52840 application. BUT,...
Hi
Two years ago our device was tested using nRFgo Studio 1.21.2.10 Direct Test Mode.
How can I know if the nRFgo software used BLE 4.2 or 5.0 during the tests? The only...
Hello,
We are making a custom application where we have several ble-mesh server nodes (nRF52832), and one of them connects to an Android app, acting as a proxy. The app...
Hi All,
I want explore BLE5 extended advertisement with nRF52832.
Using "ble_peripheral\ble_app_blinky" code from SDK16.0.0, facing " NRF_ERROR_INVALID_PARAM (7)" error...
Hi, I ported the TimeSync example devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices to the current SDK 16.0.0 and S140_nrf52_7.0.1_softdevice. But...
I am unable to set the PA/LNA Mode on NRF52832 using SDK 14.2 ( Soft Device Version S132 5.0 ) using the Fansttel BT832X SoC.
i have used the exact function on the below...
There is the nRF52840 specifications sheet at the reference circuitry there is a pin 74 that is indicated as ground, what is this? 74 does not seem to line up with the method...
I don't know if this something I'm doing wrong, a Segger stupidity, or something else. I'm using SES and copied the examples/ble_central/ble_app_blink_c project to another...
I am struggling with excess current consupmtion using uart+fifo. It seems like ~300uA is drawn by UART and disabling via app_uart_close() doesn't help.
I have checked all...
HI,
I have nRF9160 modem DK. I am working a project based on http sample.
The LTE is initialized through the call:
w_lte_lc_init_and_connect();
But after ( in the...
Hi, In my current project I'm implementing an ANT Shared Channel topology, where in each channel period the master polls a slave with an acknowledge message and receives the...
Hello,
I can connect to LTE with the iBasis SIM that came with the nRF9160DK but have been unable to connect with any other SIM. Here is what happens in the LTE Link Monitor...
