I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
I have an embedded Linux platform which uses an nRF9160 connected via UART. The nRF9160 has been loaded with the serial LTE modem firmware, version 1.3.1.
I've been experimenting...
Hi!
I'm developing the NRF9160 target from a raspberry Pi. The problem is that I need occasionally to perform modem firmware upgrade, and I can't figure out how to do it...
Hi. I am currently using an nRF52840 DK board and SDK 17.0.2.
I have add a custom characteristic in the heart rate service sample code.
The characteristic is shown on...
Hi Nordic,
I am using your official board nrf52840 to develop my application based on the ble_app_uart_peripheral example. BLE communication and the spi interfaced sensor...
Hi, I'm working with a nordic thingy:52 and SDK thingylib on Android.
The issue I'm facing is that the real sampling frequency, compared to the one indicated by the SDK...
Hello,
I try to use the ASSET_TRACKER application with NB-IoT/ Vodafone in Netherland. Vodafone uses UDP/IP datagrams protocol. is it possible to modify the asset-tracker...
So, we are using NRF52811 with external 32MHz xtal and also exeternal RTC crystal.
Every now and then we are unable to pass tests of the programmed firmware because the...
Dear Sir/Madam,
I have already developed an RF communication device with an NRF24L01+ device. And I want to migrate to nRF52833-QIAA-R. For that, I have the below questions...
I'm using RTC to wakeup every 500ms, I have Watchdog enabled but after a while (about half.. or an hour...) it will not wakeup anymore and watchdog will not reset.
I measured...
Hi, we programmed the nRF52840-DK with ble_app_hids_keyboard demo (s140) and tested with different BLE keys under a Linux PC. It worked. Tested the same configuration with...
Hi,
I have some code that normally uses nrf_crypto with the cc310 or cc310_bl backend. I was writing a unit test for this code which compiles and runs in Linux/WSL. Since...
Has anyone written a utility to dump the tables of contents (i.e. directory of files) and
an entire file with record keys:contents to a host operating system file to a file...
Hi,
I'm working on the bootloader part of a project. Using nrf Connect, the integrated MCUBoot bootloader, trying to figure out how all the parts fit together. Running into...
Hi,
As iOS developer, I'm facing a really strange issue : Using the nRF Connect app, I try to connect my BLE device, with success or not depending my iPhone/iPad configuration;...
Hi guys,
I am using the nRF52832 board on which I run the LPN example from BLE Mesh directory. I put there the code for measuring the temperature and now I want to save...
