Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Are there any specific points using the external flash of a Thingy:91X?
I tried to adapt the "nrf/samples/cellular/modem_trace_flash" by adding an overlay copied and modified...
Hello,
I am using the same hardware, and firmware on 4 custom boards of the same device. I observed that I am getting different current consumptions in each devices.
I...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
So as the title... the Creating a custom driver using the sensor API exercise for the current SDK versions is missing from the nRF Connect SDK Intermediate course. Are there...
We urgently need to add support for Band 40 (B40) to our product. Our use case is very specific, and as far as we understand, the NRF91 currently does not support B40. We...
I had a project that I made with SDK v2.6.0 and Toolchain v2.6.0 with an Actinius Icarus board.
Today I wanted to continue with my project so I build it and everything was...
Hello DevZone.
Is it possible to enable Notify and Indicate method at the same time in NCS?
From my side, this doesn't work on my project, neither on Nordic sample ...
Hello Nordic Team,
I previously asked about how to configure the internal load capacitance for the 32 MHz crystal on nRF54L, and I’ve successfully applied the solution provided...
Dear Engineer
When the advertiser and the scanner enter the connect callback, a timestamp will be printed immediately. The problem now is that the advertiser and the scanner...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello,I tryed to install the CMSIS Wirzard in SES on the video from https://www.youtube.com/watch?v=b0MxWaAjMco But it deosn't work. I don't know why. I did read the DevZone...
Hi,
I recently started working with the nRF54L15DK and nRF Connect SDK 2.9.1. I'm trying to use I2C21 and SPI00, but I noticed that certain pins on the development kit always...
Hey guys,
I just came up with an error I can't explain with my current zephyr knowledge and I really can't workaround because the other MCU isn't programmable and needs...
I am currentry trying to evaluate the RAYTAC-MDBT50Q-CX-40.
Raytac Corporation 勁達國際電子股份有限公司
But sample applications(helloworld, blinky) don't work.
I installed the...
Hi,
I was working on Channel Sounding for my NRF54L15 boards and suddenly the boards in "connected devices" were no longer visible. I don't know how it happened and what...
Hello,
Im trying to security connecting but i'm getting this bug.
After auth_passkey_display(), Next step is so late(more then 3min).
Tool : VS code
SDK : nRF...
Using VSCode and the nRF Connect VSCode extension, each time a debug session is started the target is erased and programmed, regardless of whether the code was changed.
...
Dear Nordic TS,
I'm trying to power an nRF9161 DK with a simple external battery. According to the documentation, I thought that this battery voltage should be applied between...
