Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hi,
While upmerging our project from SDK 15.3.0 to 17.0.0 we faced an issue in the sdc_handler due to usage of a NULL pointer.
In the case SDC_EVT_INIT if the p_event...
Hello,
I am experimenting with PWM for time, I have a setup where I am using three sensor which gives analogue output.
I am using a mux which has two control pins, so...
Hi all
I have just started doing some work with the nRF52840- DONGLE (and hence nRF52840-DK) and am new to Nordic devices, tools, BLE, etc.
Basically for my first application...
I'm attempting to increase the size of the TX Queue in an effort to increase notification performance.
I'm using nRF52840 with an S140 soft device. I use Segger Embedded...
Hi,
I have two nRF9160DKs and I noticed that the SHA-256 digest of the credentials looks very strange
Questions:
1, Why are the digest so repeating? I have installed...
I'm implementing the door lock cluster on the server side (the door lock device), and needs to send event commands to the client (door lock controller/gateway) . According...
Hi Team,
We are using the NRF52832 for our application and we have enabled the crypto libraries for that.
For,
1. AES-ECB,CFG,CBC modules we are using the "mbed TLS...
Hello,
We are using nRF52840 with SDK 15.2.0. In our software we have handled the DTM and we are able to send the commands using UART.
We would like to do the receiver...
Hi,
I'm developing a Bootloader for the nRF52xx chip using the SoftDevice S113 v7.0.1 and SDK v17.0.0
Looking into the infocenter I've seen that there's a possible mistake...
I have an AWS account and I am comfortable with the AWS IOT operation in general. I have used it in the past. I am trying to get the sample mqtt_simple to connect to AWS IOT...
I need to integrate 30 nodes using openthead cli , with each node connected with 8 bit controller (not computer) , to form standalone mesh network
Is it necessary to bring...
1. I refer to this link to test the low-power program on ncs v1.3, when importing this problem, please help me solve the problem with the import project.
2. The problem...
