Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I am working with the nRF54L15 and I want to use it both as a BLE central and as a BLE peripheral. So, I have two separate source files: one for central and one for...
Hi all,
nrf54l15dk,v3.0.1,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
Finally...
I have an application built on the 52840 which is using a software interrupt triggered by the event generator unit. Occasionally my SWI function is being passed a zero for...
Hi everyone,
I want to set by BLE device advertising itself for 30s and then go to sleep. To that I set the APP_ADV_DURATION = 3000. What is not clear to me is the difference...
Hello ,
I am playing with PDK NRF 5340, I am trying to write a simple code to configure a PIN (0.10) which is not already in use by PDK.
When I print it's state it always...
Hi,
nRF52 SDK Version: 16.0
Example: examples/ble_central_and_peripheral/experimental/ble_app_multirole_lesc
File: main.c
I made two different binaries of this code...
Hi,
My question is about Nrf connect for mobile but I could not find that in the product dropdown list.
I am trying to analyse packets between my mobile phone and...
Hi all,
i am using twi_scanner and twi_sensor as templates to get data from CCS811 Air Quality sensor with PCA10040 and SDK 15.3. But i cannot get the data printed in...
I really don't understand your terminologies. In beacon example you are passing BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED. It is getting scanned in NRF CONNECT...
Hi,
Trying to implement ECDH I struggled creating the random seed. Using Nordic Security Backend and Vanilla Mbedtls on the nRF5340 I get the following errors:
Minimal...
Hi,
I am developing the board to act as Broadcaster and also Observer
I am using SDK_16 with SEGGER EMBEDDED . nRF52
board wants to do Broadcast the signal ( non-connectable...
Figure 7 of the nRF24L01 data says ACK payloads must be loaded in advance to the automatic ACK transmission. I wish to make the ACK data packet dependent on what is received...
Hi：
I noticed, P0.18 P0.19 P0.21 P0.22 P0.23 P1.00，recommended as QSPI.
There is no way to raise the P0.22 pin using this code.
But my own board must use P0.22 as...
I'm been analyzing this code for a while now but can't see how this code actually triggers a switch into the Bootloader mode. There are no references to any resets or the...
Hello
I would like use at least 2PPI channels to control a GPIO.
If PPI CH0&CH1 both setup, then GPIO_CTL just go high.
If PPI CH0 remarked, then GPIO_CTL go low
How...
Hi, 1. What document can guide the macro definition of configuring the nrf9160 project? 2. How do you know that prj.conf has those macro definitions how to configure? 3. A...
