I have a zephyr zbus project running on the nrf52840DK that’s working well. We want to port the project to the nrf54H20DK, but I’m having trouble seeing the log messages....
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi
I connected RF Connect for Desktop to "nRF54L15_DK" in my Desktop
when I want to use Direct Test Mode,press Start test bottom,the log show "DTM setup reset command...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
Hello Sir,
I am currently working with the boards:52840dk and ncs:2.9.1
Regarding the issue of failed mcuboot upgrade after writing the upgrade firmware using flash APIs...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
I have this main code:
With this overlay:
and this configuration:
I am using a nrf52840 dev board and have connected P0.06 and P0.08.
Why does it not trigger...
I'm playing a bit with MCU boot and folowed the tuturial . When I compile the sample with mcuboot from Zephyr, it works fine for the 52840DK, but when I try to compile for...
NPM2100 EK CONNECTION
Can I connect The NPM2100 EK with NRF52 DK? If so..... 1. How do I physically do this? 2. Can I program the NPM2100 EK to send Voltage Supply of 1...
When using Bluetooth AOA, I configured only two antennas to collect IQ data. Below are the curves formed by the 37 IQ data points collected from the two antennas during the...
Dear Nordic Teams :
I find the NFC current and find the current is quite large in the datasheet version 0.8. The value is much bigger than nRF52840. Is it correct?
Hi,
I would like to clarify a few points related to the power saving modes of the nRF9160 and how it behaves in low-power states.
1. PSM Current Consumption — What Does...
Hello everyone!
The Quick Start mentions that the two SIM cards that come with the nrf package work right out of the box - I've tried them and they work with just activation...
Hi,
We designed our custom board using nrf54l05, and tried to flash it using segger J-lInk as well as using nrf54L15-DK Debuger out port using nrf connect Programmer utility...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
Please help. Why is QSPI not a valid peripheral option?
Environment: SDK v3.0.0 , nRF Connect for VS Code v2025.5.92 , VS Code 1.99.3, Ubuntu 22.04.5 LTS
Code copied verbatum...
