Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I was under the impression that when the voltage was 0 in a GPIO pin, reading from that pin would return 0, and if there was any voltage going through the pin it would read...
I found a Q&A that shows 1 channel 2MHz pulse but i don't know how to generate 2 channel GPIO pulse with 2MHz frequency
(one channel is inverted pulse to another channel...
This is a bit of a weird question, but I thought maybe I could get a few useful inputs here.
I'm working on a mesh-like project where we need to facilitate communication...
I would like to switch to using libUARTE for both of my UARTs but I don't have any additional timers free. Is it possible to do this and use FreeRTOS timers?
Thanks,
...
Hi,
We would like to interface with our nRF52840-DK from a PC.
We need to be able to send\recieve data from PC -> 52840 using Nordic's UART service.
We are looking for...
Hi,
We are the company which widely use your products in our devices. Currently we have the nRF9160 based device which have permanent trouble with radios. I want to ask...
Hi All,
Is there a tool or app that shows a visualization of Thread RSSI?
Any help would be appreciated, thanks in advance.
Best,
Tao
Ref:
https://devzone...
Hi,
I am developing both Central and Peripheral devices with nRF52840. For consistency, both are using SDK 15.3.0 and S140 V7.
I am able to connect to peripherals and...
Hi,
I was try to import modul nrfxlib in extising cmake project. My IDE is Eclipse CDT. Version of Zephyr is 2.4.0. Reason to do that, was testing SoftDevice BLE functionality...
We are using our board design using nRF52840.
During bringup I noticed that I could not run the Softdevice and the SPI driver simultaneous. After a bit of debugging it boiled...
I'm trying to send radio frame in timeslot but it's not working. From what I see with an spectrum analyzer, only the first frame is sent.
I am able to make the radio works...
Hi,
We are developing an application with a custom nrf5340 board in which beacons are sent periodically every 100ms. We have been analyzing power consumption with a Power...
Hi there!
We faced the problem of not being able to perform Legacy DFU with Android 10 and newer iOS devices and have since applied the fix. However, since doing so we observed...
Hello,
in our design we use a RF switch behind the ANT LTE antenna I/O of the nRF9160. Many RF switches need DC blocking capacitors in series with the RF signal due to their...
