hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
When adding the DK to my nRF cloud account, I get the following error message: " There was an error adding your device: nRFCode 40102: Ownership code [HWID] is invalid for...
nRF52840, SDK v16.0.0 SD140v7.0.1
Our electrical engineers gave us a hard ATT_MTU limit of 65 bytes, so as to keep the peak current low on the battery for our ultra-low...
Hi,
I'm running into a problem where a TWIM TX call gets stuck internally waiting on the NRF_TWIM_EVENT_STOPPED event. It never breaks out of this while loop in the twim_xfer...
Hello,
I'm trying to integrate the nrf Calendar example here with Current Time Service client implementation on a nRF52840 DK.
I'm trying to understand the logic of the...
Hi, i am new to the nRF52832, Now I want to use it in development.
I need to use it to send Running Dynamics data.
I would like to ask everyone, is there a related demo...
Dear all,
I'm developing my thesis project and I'm using 2 custom nrf52840-DK. I manage to implement BLE and the 2 boards actually connect and communicate beetween them...
Hi... I am using 15.2 version sdk , i have merged ble_app_uart and twi_sensor example code . complied successfully but while running after two output data i am getting fatal...
Hi,
I successfully added libuarte async library to the ble_app_uart example. Now I am able to receive data over UART from another board and my goal is to transfer it to...
While still trying to debug the disconnect problem in a different thread (unsuccessfully), I've gone to the ATT_MTU_THOUGHPUT example, to try and understand it and gain more...
Hi,
I am working with a custom board with a third party NRF52832 module. On my board I have a DS3231M real time clock IC communicating with the NRF52832 via I2C/TWI and...
I am trying to have a bluetooth bond between the device and the app,
how to set a security key to bond it with the android app? and also can I know how to encrypt all the...
Hi,
I have a question about getting the appkey from flash:
I am using the device state manager for key management. I do a ramdom generation of netkey and appkey on first...
I have a few different Fanstel Eval boards that contain the nRF52840 SoC - starting with the BT840XE. I'm able to flash the board with example firmware and my own custom firmware...
